Kenmore Refrigerator 253.9768384 (2539768384, 253 9768384) Parts

This is the Right side.

This lower hinge pin secures the refrigerator door to the cabinet, allowing the door to pivot smoothly and stay aligned. Replaces a worn or damaged hinge pin to restore proper door movement and closing. What it does:

• Acts as the pivot point for the refrigerator door, supporting door weight and rotation
• Helps keep the door aligned to prevent sagging, sticking, or uneven gaps
• Commonly replaced when the pin is bent, worn, or causing noisy/rough door movement
• Works with the lower hinge assembly to maintain a proper door seal and operation

• Installation requires removing the lower hinge or door; follow your model's service instructions
• Support the door while removing/installing hinge hardware to prevent injury or damage
• Use appropriate hand tools; avoid forcing parts or misaligning the hinge pin
• If any hinge housing or mounting hardware is damaged, replace those parts as well for safe operation

This rubber grommet cushions and seals appliance components to reduce vibration and prevent wear where wiring, rods or panels pass through mounting openings. It helps keep parts aligned and protects against chafing and noise. What it does:

• Cushions and isolates vibration between moving parts and chassis
• Protects wiring, tubes or rods from rubbing and abrasion at mounting holes
• Helps reduce noise caused by contact or metal-on-metal vibration
• Aids in maintaining proper part alignment and secure fit

• Grommet

• Inspect mating hole and surrounding area for debris or sharp edges before installing
• Fit the grommet into the mounting hole so the flange seats evenly on both sides
• Replace any damaged or excessively worn grommets to restore protection
• Disconnect power and follow appliance safety procedures before attempting service

This meat pan is the removable storage tray that fits inside the refrigerator cabinet to keep raw or prepared meats contained and organized. It helps reduce leaks and makes cleaning easier. What it does:

• Collects and contains meat juices and small spills to protect other refrigerator surfaces
• Provides a dedicated, easy-to-clean surface for storing raw or prepared meat
• Keeps food organized and helps prevent cross-contamination when used properly
• Stable tray design that slides into cabinet support rails or rests on shelves

• One meat pan

• Remove power to the appliance and empty surrounding shelves before installing
• Slide the pan into the cabinet supports or place on the shelf until it sits flat
• Clean with mild detergent and warm water before first use and after each use
• Do not use abrasive cleaners or sharp tools that could damage the pan

This defrost heater melts frost and ice on the evaporator so your refrigerator can maintain proper airflow and cooling. It's the heating element used during the appliance's automatic defrost cycle. What it does

• Warms the evaporator coil to remove frost and ice buildup
• Restores normal airflow through the evaporator for consistent cooling
• Helps stop frost-related symptoms like reduced cooling or ice-covered coils
• Works as part of the defrost system along with the thermostat and control timer/board

• One defrost heater

• Disconnect power to the appliance before servicing to avoid shock
• Handle the heater carefully; avoid bending or damaging the element
• Inspect and, if necessary, test the defrost thermostat/bi-metal and wiring when replacing the heater

This glass crisper cover provides a stable shelf over the refrigerator crisper drawer, helping protect produce and contain spills while keeping the drawer accessible. Restores a level surface and improves storage organization. What it does:

• Serves as the top surface above the crisper drawer so items can be stored or rolled off safely into the drawer below.
• Helps contain spills and prevents food from falling directly into the crisper compartment.
• Replaces cracked, chipped or missing glass that can cause instability or sharp edges.
• Restores proper spacing and support for items stored on the lower refrigerator shelf area.

• One glass crisper cover.

• Disconnect power to the appliance or ensure the fridge door is open and interior lights are not a hazard before you begin.
• Handle glass with care and use gloves to avoid cuts; inspect packaging for breakage before installation.
• Align the cover with the shelf supports or locating tabs and lower gently into place until it seats securely.
• If any support rails or clips are damaged, replace them before installing the new cover for a secure fit.

This replacement ice container catches and stores ice produced by the freezer ice maker so loose cubes stay contained and easy to access. Restores proper ice collection and organization in the freezer compartment. What it does:

• Collects and holds ice dispensed from the ice maker so cubes don't scatter inside the freezer
• Keeps ice organized and accessible for removal or serving
• Prevents ice from blocking the dispenser chute or falling onto shelves
• Helps maintain a cleaner freezer interior by containing drips and loose cubes

• Disconnect power to the appliance before starting any work
• Remove existing ice and, the ice maker assembly per appliance access procedure to free the container
• Slide the container into the ice bin tracks or seat it in the freezer compartment until it clicks or seats firmly
• Wash the new container in warm, soapy water and dry thoroughly before first use; avoid abrasive cleaners