Kenmore Dishwasher 363.14031000 (36314031000, 363 14031000) Parts

This hex-washer-head screw secures panels, brackets, and internal components in your dishwasher. Replacing a stripped, rusty, or missing fastener restores a tight fit, reduces rattling, and helps keep assemblies properly aligned during operation.

• Fastens components to frames, panels, and mounting brackets inside the dishwasher
• Helps maintain alignment and resist loosening from vibration
• Replaces missing, worn, or corroded screws
• Signs of trouble: loose or rattling panels, hardware that won't tighten, or a visible missing screw

• Disconnect power and water supply before servicing
• Note the original screw's location/orientation and install in the same hole
• Start threads by hand to avoid cross-threading; use the correct nut driver or socket
• Tighten snugly without over-torquing to prevent stripping

• Head style: Hex washer-head
• Size: #10-16 thread, 3/8 in length
• Sold individually

This sump cap seals the sump opening at the bottom of the dishwasher tub to contain wash water and protect the pump. Replace a cracked, loose, or missing cap to help prevent leaks and maintain proper wash performance. What it does:

• Seals the sump opening to keep water inside the tub and direct flow to the pump
• Helps keep debris out of the pump intake
• Restores a secure fit when the original cap is cracked, stripped, or warped
• Common symptoms: water leaking from the base, moisture under the dishwasher, visible damage, or a missing cap

• Disconnect power and turn off the water supply.
• Remove the lower rack and, if needed, the lower spray arm to access the sump.
• Remove the old cap and clean the sealing area; install the new cap and hand-tighten until snug—do not overtighten.
• Run a short cycle and check for leaks around the sump.

Size: 8-16 x 2 inch ss.

Color: White.

This mounting bracket kit secures the appliance cabinet for improved stability and alignment, helping stop movement, vibration, or panel gaps caused by broken or missing brackets. Restores the cabinet mounting to factory-style support. What it does

• Secures the appliance cabinet to the chassis or mounting points to keep panels aligned
• Replaces cracked, bent, or missing brackets that allow the cabinet to shift or vibrate
• Helps reduce rattling, rubbing, or movement during operation
• Provides the mounting points needed for proper panel fit and safe operation

• Disconnect power (and gas, if applicable) before starting any repairs
• Use the appliance service manual or exploded parts list for model-specific steps and correct fasteners
• Wear gloves and eye protection; handle sheet metal carefully to avoid cuts

Includes 12 retainers.

This junction box cover replaces the appliance's electrical access panel to protect wiring and provide a secure entry point for the power cord. It restores a finished, safe electrical connection area and helps prevent exposed wiring. What it does

• Covers and protects the appliance's electrical junction box from dust and accidental contact
• Provides the mounting location and opening for the power cord/strain-relief connection
• Secures wiring and helps keep wire connections contained and stable
• Common symptom: cover cracked, missing, or loose—exposed wires or inability to secure the power cord

• Disconnect power at the breaker or unplug the appliance before servicing electrical parts
• Remove mounting screws from the old cover and replace with the new cover; retain or replace strain relief as needed
• Inspect the cord and wiring while access is open; replace any damaged wiring or strain relief components
• Follow the appliance manufacturer's instructions and local electrical codes for safe installation

Size: 10-16 ab.

Replacement latch keeper for the dryer door latch assembly that secures the latch and keeps the door closed during operation. Restores reliable door engagement to help the appliance start and complete cycles. What it does:

• Secures the door latch so the dryer door stays closed during operation.
• Aligns with the latch mechanism to maintain proper door engagement.
• Common symptom: dryer door won't latch or feels loose, causing the cycle to not start or stop unexpectedly.
• Replaces worn or broken keeper pieces that allow rattling or misalignment.

• Disconnect power (unplug electric or shut off gas and breaker) before servicing.
• Access with basic hand tools; remove the door or front panel as needed to reach the keeper.
• Install carefully to avoid cracking surrounding plastic; do not force parts into place.
• After installation, verify the door closes securely and the dryer starts through a test cycle.

This float dome positions and protects the float inside the tub so the appliance can sense water level correctly. Replacing a cracked or missing float dome helps restore reliable fill control and reduces overfill or erratic fill symptoms. What it does

• Houses and guides the float so the fill sensor detects water level accurately.
• Prevents the float from sticking or catching on the tub, which can cause overfilling.
• Helps stop intermittent or continuous fill problems caused by a broken or displaced float.
• Keeps debris away from the float area to reduce false water-level readings.

• Disconnect power and water supply before accessing the tub or removing panels.
• Remove the lower access panel or kickplate to reach the float area; handle plastic parts gently to avoid cracking.
• Inspect surrounding seals and the float itself; replace any damaged components for reliable operation.
• After installation, restore power and run a short fill/drain cycle to verify correct float movement and water-level control.

This genuine replacement fill hose routes incoming water from the inlet valve to the dishwasher tub, restoring proper water delivery for washing cycles. Replaces worn or cracked hoses to help stop leaks and ensure reliable fill performance. What it does:

• Carries water from the inlet valve to the dishwasher tub during fill cycles
• Restores proper water flow when original hose is leaking, split, or clogged
• Helps prevent water damage caused by deteriorated or cracked hose sections
• Works with the dishwasher's fill and wash functions to maintain normal operation

• Disconnect power and shut off the household water supply before starting
• Inspect clamps, grommets, and fittings and replace if damaged
• Route hose without kinks and secure with proper clamps to avoid leaks

Includes 12 screws.

Size: 8-32 x 5/16 inch.

Replacement bracket that secures the flood/leak detection switch inside the appliance, keeping the switch positioned to sense unwanted water and help the leak-detection system work as intended. What it does:

• Holds the flood/leak switch in the correct position so it can detect water accumulation.
• Ensures consistent switch activation when water pools under the cabinet or base pan.
• Common repair when you find water under the appliance, persistent leaks, or when leak detection isn't responding.
• Simple, passive mounting part—no electrical function.

• Disconnect power and shut off the water supply before accessing the appliance.
• Remove the appropriate access panels to reach the bracket location; note orientation of the switch before removing.
• Reinstall bracket using the original fasteners or equivalent screws; keep parts organized during disassembly.
• Restore power/water and test the appliance for proper leak-detection operation after reassembly.

This hose clamp secures a washer or dryer hose connection to help prevent leaks and keep hoses firmly attached during operation. It's a simple replacement for worn or loose hose fasteners. What it does:

• Holds inlet or drain hose to the appliance fitting to reduce slipping and leaks
• Restores a tight seal at hose connection points that may be leaking or wobbling
• Keeps hoses positioned correctly during fill and drain cycles
• Useful when clamp is rusted, stretched, or no longer grips reliably

• One hose clamp

• Disconnect power and turn off the water supply before replacing the clamp
• Slide clamp onto hose, position over the fitting, then compress or tighten per clamp type (use pliers or screwdriver as required)
• Inspect the hose and fitting; replace the hose if cracked or damaged
• Test for leaks after restoring power and water

This is a stainless steel hex washer-head screw used to fasten and secure components. Its integrated washer head provides a broad bearing surface for a tight, durable hold in appliance assemblies.

• Secures panels, brackets, and hardware to prevent looseness and vibration
• Restores proper fastening when originals are stripped, missing, or corroded
• Stainless construction helps resist rust in moisture-prone areas
• Common symptoms of a needed replacement include rattling, loose panels, or missing hardware

• Disconnect power and, if applicable, shut off water before servicing
• Use the correct nut driver or socket for the hex head to avoid stripping
• Replace any damaged or missing fasteners in matched pairs or sets for even clamping
• Do not overtighten; snug to manufacturer torque guidance when available