Kenmore Cooktop 363.33356590 (36333356590, 363 33356590) Parts

Best Seller

Genuine Ge part

Burner Bowl Large

By: Ge

Part Number: WB31K5079

The Burner Bowl Large is an OEM component for GE gas cooktops and ranges. It refers to the metal pan that sits beneath one of the large front burners on the appliance.

Over time and with heavy use, exposed burner bowls can develop warping from intense heat. Grease and food residue buildup inside the bowl is also common and causes reduced performance if not cleaned regularly.

Symptoms of a warped or clogged burner bowl include:

Uneven or abnormal burner flame patterns
Slow boiling or heating of cookware placed above
Potential gas smells if warping allows leaks around the bowl
Residue that cannot be removed with regular cleaning

This burner bowl is also compatible with some Kenmore, Hotpoint, and RCA gas ranges.

Do-It-Yourself Stories from Customers like You Drip pans on gas cooktop were dirty Frank V. • Hampton Bays , NY • March 09, 2016

After trying to clean the drip pans on my GE gas cooktop numerous times I went online and found AppliancePartsPros.com. The parts were very affordable and they had them in stock. They even had a help section that showed me how to install them. In two days they were delivered to my doorstep and it took less than an hour to install. Now my cooktop looks brand new. Read more

Genuine Ge part

Surface Burner Valve Switch (Spark Ignition)

5.0 (2)

By: Ge

Part Number: WB24K5078

This surface burner valve switch mounts on the gas valve stem and signals the spark module when you turn the knob. Replacing a faulty switch restores consistent clicking and reliable ignition on the affected cooktop burner. What it does:

Mounts to the surface burner gas valve and closes the ignition circuit when the knob is turned to Lite
Sends power to the spark module to create the clicking needed to ignite the flame
Symptoms may include: burner won't spark, intermittent ignition, continuous clicking with knobs off, or a burner lights only when another knob is turned

What's included:

One valve switch

Install notes:

Disconnect electrical power and shut off gas supply; allow the cooktop/range to cool
Remove the knob and front panel or manifold cover to access the valve area
Note wire positions, transfer the wires to the new switch, and secure it on the valve stem in the same orientation
Reassemble, restore power and gas, then test burner ignition

This part fixes the following symptoms

Won't start

Do-It-Yourself Stories from Customers like You Clicking from ignitor mode would not stop after burner lit Jeffrey Maclachlan V. • Nederland , CO • September 03, 2017

Turned out the little switches on the knob shaft had corroded and were staying on. There was constant continuity showing with an ohm meter. Replacing the switches was very easy (always disconnect power to the unit before servicing). Bought a new ignitor module as a backup as they do go out of production after 10 years or so- another cheap and easy fix if needed in the future. Read more

Genuine Ge part

Spark Electrode Mounting Clip

5.0 (4)

By: Ge

Part Number: WB1K56

This small metal clip secures the surface burner spark electrode to its bracket or burner base, holding the tip at the proper gap for reliable ignition. Replace a missing, bent, or corroded clip to help restore consistent sparking.

Holds the surface burner spark electrode firmly in position near the burner head
Maintains correct alignment and gap so the igniter can spark to the burner
Can help with delayed ignition, intermittent sparking, or a burner that won't light
Typical signs include a loose/wobbly electrode, visible damage, or a missing clip

What's included: 1 mounting clip Install notes:

Disconnect power and shut off gas before servicing
Lift the cooktop or remove burner components to access the electrode; note clip orientation
Transfer the electrode into the new clip and seat the clip securely in its bracket or base
Avoid stressing the electrode's ceramic insulator; verify the tip is aimed at the burner rim and test ignition

Do-It-Yourself Stories from Customers like You Gas burner would not start Eileen L. • Hebron , MD • August 24, 2019

A new electrode and the great schismatics on your website. The only thing that took some time was removing the 2 screws in burner pan. Once removed it was very easy to fix. Read more

Genuine Ge part

Burner Bowl Small

5.0 (5)

By: Ge

Part Number: WB31K5078

Color: Black

Do-It-Yourself Stories from Customers like You Years of crusted on debris in burner bowls Calvin W. • Sunnyvale , CA • August 05, 2016

Repair was really simple. Removed power from stove to insure igniter would not fire. Removed parts to gain access to 2 screws securing burner bowls to stove top. Removed screws. Lifted up burner bowl and disconnected igniter wire from igniter and removed old burner bowl seal. Transferred igniter to new burner bowl and installed new burner bowl seal.Connected igniter wire and secured burner bowl assembly to stovetop with screws. Replaced parts removed earlier. Repeated process for each burner,... Read more