Kenmore Washer Dryer Combo 417.90812991 (41790812991, 417 90812991) Parts

Made to be used on washing machines, this part is a timer. This component controls the electrical parts and the duration of time of the washing machine's cycles. It controls the operation of the washing machine, including each of the cycles.When the timer will not advance, the washing machine could become stuck in a cycle and run constantly without stopping. The washing machine may not advance through the particular cycle like the washing, rinsing, or spinning and could get stuck on one of the cycles. It's important to unplug the washing machine from the electrical outlet before attempting to repair or replace any parts. The replacement process is fairly easy and takes about 15 minutes to complete.This timer is compatible with washing machines that are manufactured by the Frigidaire, Gibson, Kenmore, and White-Westinghouse brands. This part is sold individually and is sourced straight from the manufacturer itself.

This air duct seal creates a tight barrier between the dryer's lint housing and cabinet. Replacing a worn seal helps prevent air leaks, maintain proper airflow through the lint filter, and restore consistent drying performance.

• Seals the air duct/lint housing to the front panel to direct airflow through the lint screen and drum
• Helps maintain dryer efficiency and temperature control by preventing bypass air leaks
• Common symptoms of a failed seal include longer dry times, weak exhaust airflow, excess lint inside the cabinet, or lint around the door opening
• Replaces a deteriorated or missing seal to restore the intended air path

• Disconnect power; shut off gas supply for gas models
• Access the air duct by removing the lint screen and top/front panels as needed
• Remove the old seal and any residue; clean mating surfaces before installing the new seal
• Seat the duct evenly against the panel when reassembling to ensure a uniform seal

For seal only use part number 131901400.

This rubber lid bumper cushions the washer lid to prevent hard contact and reduce noise and wear. It replaces a worn or missing bumper to help the lid close more softly and sit level. What it does:

• Acts as a soft contact point between the lid and cabinet to absorb impact
• Reduces lid slamming, rattling, and vibration during operation
• Helps keep the lid aligned and prevents cosmetic damage to the rim
• Commonly replaced when the bumper is cracked, flattened, or missing

• One rubber lid bumper

• Install by removing the old bumper and pushing the new bumper into the mounting hole or recess; hand tools may be helpful
• Ensure the appliance is powered off and disconnected before servicing
• Inspect surrounding mounting area for damage and replace any broken retainers as needed
• If the bumper is hard to seat, warm it briefly with a hair dryer to improve flexibility

This inlet hose connects the household water supply to the refrigerator's water system so ice makers and dispensers receive a steady water feed. Durable, flexible tubing replaces worn or leaking supply lines to restore proper water flow. What it does:

• Channels incoming water from the home supply to the refrigerator's water valve and ice maker
• Replaces cracked, split, or leaking supply tubing that can cause reduced water flow or puddling
• Helps prevent leaks that can lead to water damage when original tubing fails
• Works with the fridge's internal water system to support ice and dispenser functions

• One inlet hose (single water supply line)

• Turn off the home water supply and unplug the appliance before servicing
• Inspect fittings for signs of corrosion; use the proper connector tools to avoid damage
• Tighten connections to a leak-free fit but avoid over-tightening plastic fittings

This wiring clip secures a refrigerator's wire harness to the cabinet or components to prevent chafing and keep wires organized. It helps maintain safe routing and reduces strain on electrical connections. What it does

• Holds wiring harness in place to prevent rubbing against sharp edges or moving parts
• Keeps wires organized to reduce the risk of pinching or accidental disconnection
• Helps prevent intermittent electrical faults caused by loose or strained wiring
• Commonly used near compressor, fan, control box, or rear cabinet areas

• Install by snapping the clip onto the cabinet flange or component and routing the harness through the retainer
• Disconnect power before accessing electrical components or wiring
• Inspect surrounding wiring and insulation; replace any damaged wire or harness tape before reinstalling the clip

This push-in fastener secures plastic trim and interior panels to the appliance chassis, restoring a snug fit and reducing rattles or gaps. Simple, durable replacement for worn or missing retainers. What it does:

• Secures trim pieces, door panels, or interior components to the cabinet
• Keeps panels aligned to prevent vibrations and rattling noises
• Replaces missing or broken retainers that allow gaps or loose trim
• Works where a snap-in or push-retainer style fastener is specified

• Disconnect power to the appliance before servicing to avoid electrical risk.
• Remove surrounding trim or panels as needed to access the mounting hole.
• Push the fastener into the panel hole until it snaps or seats fully; ensure a flush fit.
• Replace with an identical fastener if size or stem design differs.

Hex washer head. 5/16-18 x 0.625