Kenmore Washer Dryer Combo 417.97864790 (41797864790, 417 97864790) Parts

This mechanical cycle timer controls the sequence and duration of wash, rinse and spin functions in compatible top-load washing machines, restoring proper cycle advancement and timing. What it does:

• Advances the washer through timed cycles so selected wash, rinse and spin functions run in the correct order.
• Routes power to the washer's motor and valves at the right points in the cycle.
• Commonly replaces timers that cause machines to get stuck on one cycle, fail to advance, or not complete a cycle.
• Works with the machine's existing control knobs and wiring harness to restore automatic cycle sequencing.

• Disconnect power to the washer before beginning any service to avoid electrical shock.
• Service typically requires access behind the console or control panel; remove panels carefully and keep fasteners organized.
• Note and photograph wiring connections before removal; reconnect wires to the same terminals.

For seal only use part number 131901400.

This rubber lid bumper cushions the washer lid to prevent hard contact and reduce noise and wear. It replaces a worn or missing bumper to help the lid close more softly and sit level. What it does:

• Acts as a soft contact point between the lid and cabinet to absorb impact
• Reduces lid slamming, rattling, and vibration during operation
• Helps keep the lid aligned and prevents cosmetic damage to the rim
• Commonly replaced when the bumper is cracked, flattened, or missing

• One rubber lid bumper

• Install by removing the old bumper and pushing the new bumper into the mounting hole or recess; hand tools may be helpful
• Ensure the appliance is powered off and disconnected before servicing
• Inspect surrounding mounting area for damage and replace any broken retainers as needed
• If the bumper is hard to seat, warm it briefly with a hair dryer to improve flexibility

This wiring clip secures a refrigerator's wire harness to the cabinet or components to prevent chafing and keep wires organized. It helps maintain safe routing and reduces strain on electrical connections. What it does

• Holds wiring harness in place to prevent rubbing against sharp edges or moving parts
• Keeps wires organized to reduce the risk of pinching or accidental disconnection
• Helps prevent intermittent electrical faults caused by loose or strained wiring
• Commonly used near compressor, fan, control box, or rear cabinet areas

• Install by snapping the clip onto the cabinet flange or component and routing the harness through the retainer
• Disconnect power before accessing electrical components or wiring
• Inspect surrounding wiring and insulation; replace any damaged wire or harness tape before reinstalling the clip

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support

A coiled roll pin used to secure shafts, rollers, or linked components in place, helping maintain proper alignment and smooth operation. Ideal when a worn or damaged pin allows movement or causes noisy parts. What it does:

• Secures shafts, rollers, or pivots by fitting into a mating hole to prevent axial movement
• Keeps rollers and linked components aligned for smooth rotation and operation
• Common symptom: loose or wobbling roller/shaft or parts that shift during use
• Common symptom: unusual noise or intermittent binding where a pin retains a component

• Disconnect power to the appliance before beginning any work
• Removal/installation may require a punch and hammer or pliers; protect surrounding surfaces
• Replace with the exact part number to ensure correct fit and retention
• Keep small parts away from children and pets

This door gasket creates a tight seal around the refrigerator door to help maintain proper cooling and reduce energy loss. Replacing a worn gasket restores a full seal for better temperature control and food preservation. What it does:

• Seals the door to prevent warm, humid air from entering the refrigerated compartment
• Helps reduce frost buildup and keeps interior temperatures stable
• Improves cooling efficiency and can lower energy use caused by a leaking seal
• Stops odors and moisture transfer between the fridge interior and kitchen

• Unplug the refrigerator before starting and remove any food or shelves blocking the seal.
• Work slowly to avoid stretching or creasing the gasket; follow door-hinge or trim removal steps if needed.
• Inspect the door flange for damage and clean the mating surface before installing the new gasket.
• After installation, allow the gasket to seat fully and check for uniform contact around the door; warm-up or seating time may be needed.