Kenmore Washer Dryer Combo 417.99370110 (41799370110, 417 99370110) Parts

This block is a small mounting spacer used to secure and align components inside the appliance, helping maintain proper fit and operation. It replaces worn or broken mounting blocks to restore stable support and alignment. What it does:

• Provides a stable mounting surface or spacer between cabinet components
• Holds panels or assemblies in correct position to prevent rubbing or misalignment
• Helps reduce vibration or shifting of the connected parts during operation
• Commonly replaced when cracked, broken, or missing

• One mounting block

• High-level replacement; may require removing panels or trim to access mounting location
• Use appropriate hand tools and keep fasteners organized for reassembly
• Disconnect power before servicing any electrical components

This inlet hose connects the household water supply to the refrigerator's water system so ice makers and dispensers receive a steady water feed. Durable, flexible tubing replaces worn or leaking supply lines to restore proper water flow. What it does:

• Channels incoming water from the home supply to the refrigerator's water valve and ice maker
• Replaces cracked, split, or leaking supply tubing that can cause reduced water flow or puddling
• Helps prevent leaks that can lead to water damage when original tubing fails
• Works with the fridge's internal water system to support ice and dispenser functions

• One inlet hose (single water supply line)

• Turn off the home water supply and unplug the appliance before servicing
• Inspect fittings for signs of corrosion; use the proper connector tools to avoid damage
• Tighten connections to a leak-free fit but avoid over-tightening plastic fittings

This wiring clip secures a refrigerator's wire harness to the cabinet or components to prevent chafing and keep wires organized. It helps maintain safe routing and reduces strain on electrical connections. What it does

• Holds wiring harness in place to prevent rubbing against sharp edges or moving parts
• Keeps wires organized to reduce the risk of pinching or accidental disconnection
• Helps prevent intermittent electrical faults caused by loose or strained wiring
• Commonly used near compressor, fan, control box, or rear cabinet areas

• Install by snapping the clip onto the cabinet flange or component and routing the harness through the retainer
• Disconnect power before accessing electrical components or wiring
• Inspect surrounding wiring and insulation; replace any damaged wire or harness tape before reinstalling the clip

This replacement control panel restores the appliance's front console appearance and provides the mounting surface for the user controls. It lets you replace a cracked, faded, or damaged console so controls sit and function correctly. What it does:

• Replaces a damaged or cracked front console panel and restores a finished appearance
• Provides the mounting surface and protection for switches, touchpads, and display components
• Helps stop drafts or light leaks from a broken panel that affect user access
• Common symptoms: visible cracks, broken mounting tabs, loose or rattling console, or exposed control openings

• Disconnect power before beginning any repairs to avoid shock; if applicable, unplug the appliance or switch off the breaker
• Handle panels carefully to avoid cutting on sharp edges or damaging attached trim pieces
• Some installations require removing trim pieces, fasteners, or the control assembly; keep hardware organized for reassembly

A coiled roll pin used to secure shafts, rollers, or linked components in place, helping maintain proper alignment and smooth operation. Ideal when a worn or damaged pin allows movement or causes noisy parts. What it does:

• Secures shafts, rollers, or pivots by fitting into a mating hole to prevent axial movement
• Keeps rollers and linked components aligned for smooth rotation and operation
• Common symptom: loose or wobbling roller/shaft or parts that shift during use
• Common symptom: unusual noise or intermittent binding where a pin retains a component

• Disconnect power to the appliance before beginning any work
• Removal/installation may require a punch and hammer or pliers; protect surrounding surfaces
• Replace with the exact part number to ensure correct fit and retention
• Keep small parts away from children and pets

This door gasket creates a tight seal around the refrigerator door to help maintain proper cooling and reduce energy loss. Replacing a worn gasket restores a full seal for better temperature control and food preservation. What it does:

• Seals the door to prevent warm, humid air from entering the refrigerated compartment
• Helps reduce frost buildup and keeps interior temperatures stable
• Improves cooling efficiency and can lower energy use caused by a leaking seal
• Stops odors and moisture transfer between the fridge interior and kitchen

• Unplug the refrigerator before starting and remove any food or shelves blocking the seal.
• Work slowly to avoid stretching or creasing the gasket; follow door-hinge or trim removal steps if needed.
• Inspect the door flange for damage and clean the mating surface before installing the new gasket.
• After installation, allow the gasket to seat fully and check for uniform contact around the door; warm-up or seating time may be needed.