Kenmore Dishwasher 587.1530590 (5871530590, 587 1530590) Parts

A single #8A x 1/2" screw used to fasten trim, panels, and internal components on compatible appliances. Small but essential, it restores secure mounting and stops loose parts from rattling or shifting. What it does:

• Secures panels, brackets, and trim to the appliance chassis
• Replaces missing, stripped, or corroded screws that cause rattling or loose fittings
• Provides proper thread engagement for consistent, reliable fastening
• Helps maintain alignment of components that depend on a correctly sized screw

• Disconnect power to the appliance before working on any electrical or mechanical components
• Use the correct screwdriver or bit to avoid stripping the head
• Thread carefully and avoid overtightening; snug is usually sufficient for sheet-metal fastening
• Keep removed fasteners in a small container to avoid loss during reassembly

This replacement mounting screw secures panels and components in compatible Frigidaire appliances, helping restore stable assembly and safe operation. It's a direct-fit fastener used where the original screw has been lost or damaged. What it does

• Fastens appliance panels, brackets, and small parts to restore secure assembly
• Replaces stripped, rusted, or missing screws that can cause rattling or loose components
• Matches the OEM fit for reliable retention and alignment during normal use

• Use the correct size driver to avoid stripping the head; tighten until snug but do not overtighten
• Disconnect power or follow appliance-specific safety procedures if working near electrical components
• Inspect surrounding hardware and replace as needed

These mounting screws secure assemblies and panels so components stay aligned and stable during normal use. Durable plated steel fasteners help maintain a proper fit and keep parts from loosening over time. What it does:

• Fastens panels, brackets, or components to the appliance frame or assemblies
• Keeps moving parts aligned to prevent vibration and rattling
• Replaces missing or stripped mounting hardware that can cause loose doors or panels
• Used wherever the original mounting screws were removed or damaged

• Turn power off and unplug the appliance before beginning any repair.
• Use the correct screwdriver or bit to avoid stripping the screw head.
• Replace only the screws removed from the same location; match size and thread when possible.
• If a screw hole is damaged or loose, inspect the surrounding area and repair per OEM guidance.

This washer heater assembly heats and maintains wash water temperature to improve detergent performance and cleaning for temperature-sensitive cycles. Designed as a direct replacement part for compatible top- and front-load machines. What it does:

• Heats incoming water to reach selected cycle temperatures for better soil removal.
• Helps maintain water temperature during the wash portion of the cycle.
• Common symptom: washer runs but water stays cold or loads are not cleaned as expected.
• Common symptom: water temperature error codes or washer fails temperature-sensitive cycles.

• Disconnect power and water supply before starting any repair.
• Handle the heating element and wiring with care; avoid damage to terminals and gasket surfaces.
• Installation may require removal of access panels and basic hand tools.
• After installation, restore power and run a short test cycle to check for leaks.

This replacement housing is the outer support shell that secures and protects internal components, restoring proper fit and alignment for the affected area. It helps stop movement and prevents damage from continued use. What it does:

• Provides structural support and a mounting surface for nearby components
• Protects internal parts from physical damage and debris
• Helps reduce vibration and rattling caused by a cracked or loose housing
• Can restore correct alignment when a worn or broken housing causes gaps or misfit

• Disconnect power (and water, if applicable) before starting any repair
• Use basic hand tools; handle edges carefully to avoid cuts
• Inspect surrounding fasteners and brackets; replace any damaged hardware
• Follow model-specific service instructions and diagrams when reinstalling

This blower clamp secures the dryer/freezer/blower assembly so the fan stays aligned and stable during operation, helping reduce vibration and loud rubbing noises. It's a simple replacement that restores proper blower support. What it does:

• Fastens the blower housing or wheel securely to its mount to prevent wobble
• Keeps the blower aligned for consistent airflow and efficient operation
• Helps stop rubbing, scraping, or rattling noises caused by a loose blower
• Prevents wear to adjacent components caused by an unsecured blower

• Disconnect power before servicing and follow all safety guidelines for your appliance
• Remove the access panel and blower housing to reach the clamp; note orientation before removal
• Replace the clamp if bent, cracked, or missing and tighten so the blower is held firmly without binding
• Inspect surrounding seals, screws, and the blower wheel for damage while servicing