Kenmore Refrigerator 596.50019100 (59650019100, 596 50019100) Parts

This drier is the factory replacement air/gas flow assembly that helps maintain proper airflow and drying performance in compatible laundry dryers. Replacing a worn drier restores consistent drying and reduces overheating risk. What it does:

• Directs and stabilizes heated air through the drum for efficient drying
• Helps prevent restricted airflow that can cause long dry times or damp laundry
• Supports safe exhaust flow to reduce the chance of overheating or lint buildup
• Works with the dryer's heating and ventilation components to maintain normal operation

• One drier assembly as shown

• Disconnect electrical power before beginning service; if this is a gas dryer, turn off and disconnect the gas supply
• Follow the dryer manufacturer's service manual for disassembly and reassembly steps
• Use appropriate hand tools and avoid forcing parts; inspect venting and lint traps while replacing

This is a replacement machine screw sized 8-18 x 3/8 that secures panels and components on compatible appliances. It restores proper fastening where a worn, stripped, or missing screw causes loose parts or rattling. What it does

• Fastens control panels, trim pieces, or brackets to the appliance chassis
• Replaces stripped, corroded, or missing screws that cause loose panels or vibrating noise
• Provides correct thread engagement for a secure hold in tapped holes
• Small hardware solution often used during door, console, or interior repairs

• One 8-18 x 3/8 machine screw (quantity: 1)

• Use the correct screw size and thread; do not force a different-size fastener into tapped holes
• Hand-start the screw to avoid cross-threading, then tighten with the appropriate screwdriver
• Disconnect power before accessing internal components or panels on electrical appliances
• If metal threads are damaged, repair with a helicoil or replace the damaged component rather than over-torquing

This genuine replacement screw secures panels and components so your appliance stays stable and trim pieces fit properly. It's a simple, exact-fit fastener intended to replace a missing or damaged mounting screw. What it does:

• Fastens panels, trim, control housings or brackets to the appliance frame
• Restores secure fit when a screw is missing, stripped, or corroded
• Helps eliminate rattling or loose panels caused by a missing fastener
• Matches OEM thread and head style for correct seating and torque

• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten; snug until parts are firmly seated
• Disconnect power and follow appliance safety guidelines before servicing

Size: 8-32 x .312 inch.

The Light Bulb Socket is an OEM part for Whirlpool refrigerators. It is responsible for housing the bulb that illuminates the interior fridge light. The socket provides a protective casing and stable electrical connection for the light bulb. Its interior components are precisely arranged to safely conduct current to the bulb. 

Causes of a bad light bulb socket can include cracks, loose connections, or damaged internal wiring due to regular use over time.

Symptoms of a bad light bulb socket include:

• The fridge interior light failing to turn on
• The bulb burning out quickly  
• Flickering or intermittent lighting

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This refrigerator deli drawer pan provides a dedicated spot for meats and cheeses in the fresh food section. Replacing a cracked or missing pan restores smooth sliding access and helps keep your refrigerator organized. What it does:

• Provides a designated bin for deli items in the fresh food compartment
• Slides on existing drawer tracks/guides for easy access
• Helps contain small spills and keep similar items together
• Common symptoms include cracks, broken tabs, poor sliding, or a missing bin

• 1 deli drawer pan

• Remove contents from the old drawer and slide the pan straight out of the guides
• Align the new pan with the tracks and push in until fully seated and sliding smoothly
• Inspect the supporting shelf and rails for damage; replace if worn or broken
• No tools typically needed; disconnect power if removing shelves or working near electrical components

This genuine-style freezer door gasket creates a tight seal between the freezer door and cabinet to help maintain cold temperatures and reduce frost buildup. Replacing a worn gasket restores a proper seal and improves cooling efficiency. What it does:

• Seals the freezer door to keep cold air in and warm air out
• Helps prevent frost and ice buildup inside the freezer
• Reduces compressor run time caused by air leaks
• Can stop visible gaps or drafts around the freezer door edge

• Disconnect power and remove food before replacing the gasket; allow the freezer to reach room temperature if iced over
• Clean and dry the door sealing surface thoroughly before installing the new gasket
• Warm or flex the gasket slightly to seat it evenly in the channel; avoid overstretching
• Inspect the door retainer and ensure the gasket sits fully in the channel; use only appropriate, non-sharp tools to avoid damage

Replacement thermostat kit restores accurate temperature sensing so the appliance can maintain correct operating temperatures. Use this kit when a failing thermostat causes inconsistent temps or frequent cycling. What it does:

• Senses internal temperature and signals the control to turn heating or cooling on and off.
• Helps the appliance maintain stable temperatures and proper cycle behavior.
• Commonly replaced for inconsistent temperatures, failure to reach set temperature, or excessive cycling.
• Matches OEM function for direct replacement of the original thermostat kit.

• Disconnect power (unplug or shut off circuit) before starting any repair.
• Follow the appliance's service manual for correct routing and secure mounting of the sensor or capillary.
• Handle the sensor/capillary gently to avoid kinks or damage.

This is a large crisper frame that replaces damaged or cracked drawer trim to restore proper fit and appearance for the refrigerator crisper area. It supports the crisper drawer and helps keep the drawer aligned for smooth operation. What it does:

• Replaces a broken or cracked crisper frame that can cause drawer binding or misalignment
• Supports and guides the large crisper drawer so it opens and closes smoothly
• Helps maintain a tidy seal and appearance around the crisper opening
• Can reduce rattling or rocking of the crisper drawer when damaged

• Disconnect power to the appliance before beginning any service.
• Removal of the crisper drawer and nearby shelves may be required to access the frame.
• Frame typically snaps or screws into place; retain original fasteners or refer to your model's service manual for reassembly.

This condenser fan blade is the rotating plastic blade that moves air across the condenser coils to help remove heat from the refrigerator. Replacing a damaged blade restores proper airflow for more consistent cooling. What it does:

• Spins on the condenser fan motor to circulate air over condenser coils
• Helps dissipate heat so the compressor and fridge run efficiently
• Can cause reduced cooling or higher temperatures if broken or missing

• Disconnect power to the appliance before starting any service
• Inspect the fan motor shaft and mounting for wear; replace motor if shaft is damaged
• Handle the blade carefully to avoid cracking; ensure blade is seated and secured before testing

This door hinge is a direct-fit replacement that helps the appliance door open and close smoothly and stay properly aligned to prevent rubbing or gaps. Durable construction restores reliable door movement and seal engagement. What it does:

• Supports and pivots the appliance door so it opens and closes correctly
• Maintains correct door alignment to help the gasket seal fully
• Reduces sagging, sticking, or uneven door gaps that can affect performance
• Works with the existing hinge mount points and hardware

• One door hinge

• Disconnect power and empty the door before starting to avoid injury or damage
• Use the OEM mounting screws and follow turning sequence to re-align the door
• Tighten fasteners securely, then cycle the door and check for proper seal and operation