Kenmore Dishwasher 665.13033K110 (66513033K110, 665 13033K110) Parts

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

12 Ft in length

This insulation pad installs in the factory location to isolate and cushion components or panels. It helps reduce vibration and limit unwanted heat transfer, supporting quieter operation and proper performance where the original pad was installed.

• Provides a thermal and acoustic barrier between parts or panels
• Helps minimize vibration and rattling noises
• Restores proper spacing/cushioning when the original pad is missing or deteriorated
• Replace if the pad is brittle, compressed, contaminated, or falling off
• Common signs include increased noise or rattles and localized hot spots or condensation

• Disconnect power (and gas/water, if applicable) before servicing
• Allow hot or cold surfaces to return to a safe temperature
• Note the original pad's location/orientation; remove old pad and clean the surface
• Install the new pad in the same spot without over-compressing; secure per the original method and verify clearances

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This overfill protector housing mounts in the dishwasher tub floor to guide the overfill float and position the switch actuator. Replacing a damaged housing helps stop leaks at the float opening and restores proper overfill protection.

• Guides the overfill float at the tub floor so it moves freely
• Allows the float to engage the overfill switch and stop water fill at high level
• Restores proper fit if the original housing is cracked, warped, or missing
• Typical symptoms include leaking near the float, overfilling, or inconsistent fill levels

• Disconnect power and shut off water supply before servicing
• Remove the toe panel and lower rack to access the float area
• You may need to lift out the float and remove the under-tub switch bracket to replace the housing; note part orientation
• After reassembly, run a brief fill and check for leaks at the float opening

This replacement screw secures appliance panels and components so they stay tight and aligned. Replace a missing, rusty, or stripped fastener to restore a solid hold and reduce vibration or rattling during operation. What it does:

• Fastens and secures panels, brackets, trim, or internal components as specified for your model
• Replaces missing, corroded, or stripped hardware to restore a proper fit
• Helps prevent vibration, rattling, and misalignment caused by loose fasteners
• Addresses issues like a loose panel/handle or a screw head that's rounded off

• 1 screw

• Disconnect power; if applicable, shut off gas and water before servicing
• Use the correct driver size; start by hand to avoid cross-threading
• Tighten snugly—do not overtighten into plastic or thin sheet metal
• Keep track of original screw locations and lengths during reassembly

The Rack Wheel is an OEM part for Whirlpool dishwashers. As an internal component that guides dish rack movement, the rack wheel works along the rack rail system to smoothly raise and lower racks in and out of the wash chamber. 

Causes of a bad rack wheel can include normal wear stripping lubrication from prolonged usage, or accidental impacts warping its circular shape.  

Symptoms of a bad rack wheel include: 

• Difficulty pulling out or pushing in dish racks  
• A rack that gets stuck and does not fully recline or rise
• Rack trays that cannot pivot to different levels during a cycle
• Reduced wash effectiveness from poor rack positioning

This OEM Whirlpool part is also compatible with some Maytag, KitchenAid, and GE dishwashers.

Restore worn dishwasher racks and help prevent rust stains on dishes. This white rack repair kit covers chipped or exposed rack tines and caps bare metal to reduce corrosion and extend the useful life of your racks.

• Re-coats rusted or chipped vinyl on rack tines to help stop corrosion
• Caps exposed tips to reduce rust transfer, scratching, and snags
• Useful when tine caps are missing or the rack coating is flaking
• Common symptoms: rust on tines, stained dishes, sharp/rough tine ends

• Disconnect power and remove the rack before repair
• Clean and dry affected areas thoroughly before applying coating
• Apply in a well-ventilated area; allow full cure time before using the dishwasher
• Replace the rack if metal is severely corroded or broken

The feed tube assembly routes wash water up the back wall of your dishwasher to the upper spray system, restoring balanced spray pressure and coverage on the upper rack when the original tube is cracked, warped, leaking, or obstructed. What it does:

• Directs water from the circulation pump to the upper spray system via the rear manifold/docking port
• Maintains a sealed path to prevent internal leaks and pressure loss
• Damage or clogs can cause poor top-rack cleaning, weak spray, noisy operation, or residual detergent
• Visible cracks, broken tabs, or leaks at the rear wall indicate replacement is needed

• Feed tube assembly

• Disconnect power and shut off the water supply before servicing
• Open the door and remove racks as needed; release screws/clips securing the rear feed tube and detach from the docking port
• Transfer any reusable seals or brackets; align and secure the new tube without overtightening plastic fasteners
• Run a short cycle to check for leaks and proper upper-spray operation

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

This fine mesh plastic screen filters debris from the water path to protect downstream components and help maintain proper wash performance.

• Traps fine particles to prevent clogs in the circulation/inlet path
• Helps reduce spray pressure loss and poor cleaning results
• Can address issues like gritty residue, reduced water flow, or noisy pump operation
• Wear, mineral buildup, or tearing can require replacement

• Disconnect power and shut off water before service
• Note orientation and seating of the original screen; install the replacement fully and evenly
• Inspect surrounding seals and mating parts; clean any sediment before reassembly
• Restore power/water and check for leaks and proper operation

Replacement 8-32-thread screw used to secure panels, brackets and small components in compatible household appliances. Restores missing or stripped fasteners so panels and parts stay firmly attached during normal use. What it does:

• Secures trim, panels, brackets and control housings to maintain proper assembly.
• Replaces missing or damaged screws that can cause rattling, loose panels or misaligned components.
• Fits locations that require an 8-32 threaded fastener; correct length and head style for your application.
• Helps restore stable, vibration-free operation when worn or stripped fasteners are replaced.

• Disconnect power and water before servicing; wear eye protection and gloves.
• Use the correct screwdriver or driver bit to avoid stripping the screw head.
• Do not overtighten—turn until snug and secure to avoid damaging threads or surrounding parts.
• If the original used a washer or nut, reuse or replace as needed and the screw length and head type match the original.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

Size: 8-18 x 1/2 inch.

A small metal clip that secures the appliance's ground wire to the chassis. Restores a reliable ground connection to reduce loose or arcing contacts and help prevent intermittent electrical faults. What it does:

• Secures the ground wire to the appliance frame to maintain a solid earth connection.
• Prevents a loose ground that can cause arcing, intermittent power issues, or visible sparking at the connection.
• Holds the wire in place through normal vibration and movement so terminals stay tight and stable.
• Replaces damaged, bent, or missing grounding fasteners to restore safe electrical continuity.

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the clip.
• Use proper hand tools to remove and reinstall the screw or fastener that holds the clip—do not overtighten.
• Ensure the ground wire is routed and stripped correctly; replace wiring if insulation or conductor is damaged.

This brace connector secures a support brace inside the appliance to help keep internal panels and assemblies aligned and stable. Replacing a worn or damaged connector restores proper support and reduces noise and movement. What it does:

• Fastens and stabilizes an internal support brace or frame
• Prevents panel or assembly movement that can cause vibration or rattling
• Helps maintain proper alignment of connected components
• Replaces broken or corroded connector hardware to restore secure mounting

• One brace connector

• Disconnect power (and gas, if applicable) before starting any repair
• Access may require removing outer or control panels; save existing fasteners for reuse
• Use basic hand tools; avoid overtightening to prevent cracking plastic or bending metal
• Inspect and replace as needed