Kenmore Dishwasher 665.13039K110 (66513039K110, 665 13039K110) Parts

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

This support bracket helps hold internal components in place to restore proper alignment and reduce movement. It's a simple replacement that stabilizes the affected assembly and helps stop rattling or sagging. What it does:

• Secures and supports a loose or misaligned internal component or panel
• Prevents shifting that can cause vibration, noise, or uneven operation
• Restores proper alignment to reduce wear on adjoining parts
• Functions as the OEM replacement for the original support bracket

• One support bracket

• Inspect the mounting points and surrounding parts for wear before installing
• Replace only with the matching OEM part number to ensure fit; fasten securely per manufacturer torque recommendations
• Disconnect power and follow basic safety precautions before servicing the appliance

This insulated wire lead carries electrical current between components, restoring reliable power routing in your appliance. It's a direct-replacement discrete wire used where a single conductor is required for safe operation. What it does:

• Provides a single insulated conductor to connect terminals or components
• Restores proper electrical continuity when a wire is damaged, burned, or disconnected
• Helps prevent shorts by maintaining insulation between conductors
• Suitable for low- to moderate-current wiring routes within the appliance

• One insulated wire lead as shown

• Disconnect power before inspecting or replacing wiring to avoid shock or injury
• Route the wire as the original, avoiding sharp edges and heat sources; secure with existing clips or ties
• Replace any damaged terminals, connectors, or fasteners; use correct crimps or solder joints per OEM practice

Color: Black - Part has been changed to an Access Panel Kit - The toe panel is no longer used.

This electronic control board is the appliance's central controller. It interprets user inputs and sensor signals to power components at the right time, restoring reliable operation when the original board fails.

• Interprets user settings and manages cycle timing and temperature control
• Switches relays/outputs to run motors, heaters, valves, fans, and lights
• Interfaces with sensors and safety switches to protect the appliance
• Symptoms can include no display or response, won't start, cycles that won't advance, or erratic operation
• Logs diagnostic error codes to aid troubleshooting

• Disconnect power before servicing; follow ESD precautions and handle the board by the edges
• Access the control area, then note/photograph wiring and move connectors one at a time to the new board
• Mount securely, ensure no wires are pinched, reassemble, and restore power
• Run a diagnostic or test cycle to confirm normal operation

This connector links mating components within the appliance to create a secure, reliable connection. Replacing a cracked or loose connector helps restore consistent operation and prevent intermittent issues caused by poor contact or separation. What it does:

• Creates a stable connection between mating parts or harnesses in the appliance
• Helps prevent looseness or separation that can disrupt performance
• Direct replacement for broken, brittle, or deformed connectors
• Can resolve intermittent operation traced to a poor connection at this junction

• 1 connector

• Disconnect power and, if applicable, shut off water before servicing
• Note orientation and positions before removal to ensure correct reassembly
• Seat the connector fully until any locking features engage; do not force
• Inspect mating parts for wear or damage and replace if necessary

Color: White

This replacement wheel installation leg restores mobility and stable support for appliances that use a leg-mounted rolling wheel. It provides a direct-fit restore of worn or damaged legs to help move and position the appliance safely. What it does

• Replaces a damaged or worn wheel-style leg that supports and helps roll the appliance
• Restores smooth rolling and stabilizes appliance during movement
• Helps resolve symptoms like a broken/collapsed leg, stuck wheel, or uneven appliance height
• Matches OEM form and fit for direct replacement when the original leg/wheel is worn

• One wheel installation leg

• Turn off and unplug the appliance and remove contents or shelves as needed before working underneath
• Use basic hand tools; avoid forcing components—reuse existing fasteners

Color: White. Size: 1 qt. can. Acrylic appliance paint.

The Inner Door Panel is an OEM part for Whirlpool dishwashers. Located inside the dishwasher door, this hard-wearing panel protects internal components from impact during loading. 

Symptoms of a bad inner door panel can include cracks or dents developing from normal use over many years. Mineral deposits may cause premature deterioration of door panel materials.

Causes of a bad inner door panel include repeated contact with dishes placed inside the washer door. Water pressure during cycles also contributes to standard wear and tear.

Symptoms of a bad inner door panel include:

• Damage exposes internal tubing, hoses, or electronics to risk
• Loss of protected support allows the door to bow outward  
• Compromised integrity permits unwanted vibration transfer 
• Reduced lifespan expectancy of door mount fittings and seals

This Whirlpool OEM replacement restores proper protection and structure. Compatible models include some KitchenAid, Jenn-Air, and select Kenmore units.