Kenmore Dishwasher 665.13163K703 (66513163K703, 665 13163K703) Parts

The Door Hinge (RH) is an OEM replacement part for Whirlpool dishwashers. This hinge is installed on the right-hand side of the dishwasher door, allowing it to open and close smoothly while maintaining the proper tension and alignment. The hinge plays a crucial role in ensuring the door seals securely during operation, preventing leaks and enabling efficient cleaning performance.

Common causes include regular use leading to wear and tear, accidental impacts, or exposure to moisture, which can contribute to rust or corrosion.

Symptoms of a bad door hinge include:

• The dishwasher door not closing completely
• Difficulty opening or closing the door
• A sagging or misaligned door
• Unusual noises when moving the door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This center basket lid secures the top of the washer basket and helps keep laundry contained during the wash and spin cycles. It replaces a cracked or missing lid to restore proper operation and reduce fabric snags. What it does:

• Covers the center of the tub/basket to keep clothes from catching on the agitator or basket edge
• Helps maintain balanced load containment during agitation and spinning
• Prevents small items from falling into the basket gap or drain area
• Restores the washer's intended interior protection and appearance

• One center basket lid

• Disconnect power and water supply before starting any repair
• Remove the dispenser/console or top panel only if required by your model; follow factory service instructions
• Handle replacement parts carefully to avoid scratching the tub or lid finish

This fine screen is the small mesh filter that sits in the dishwasher sump to catch food particles and help protect the pump and wash system. It keeps debris from circulating so dishes rinse more effectively. What it does:

• Traps food and debris in the sump to prevent clogging and pump damage
• Helps maintain proper water flow for consistent wash and drain performance
• Reduces risk of food redepositing on dishes during cycles
• Commonly replaced when torn, heavily clogged, or missing

• One fine mesh sump screen

• Turn off power and disconnect the dishwasher before servicing
• Remove the lower dish rack and access the sump area to replace the screen
• Inspect surrounding seals and housing for damage while servicing
• No special tools typically required; handle mesh gently to avoid deformation

This replacement lever operates the overflow/level switch assembly to help the washer detect and respond to water level changes. It restores the mechanical action that tells the control when the tub is full. What it does:

• Moves the overflow/level switch mechanism so the machine can sense water level correctly
• Helps address overfilling, continuous filling, or erratic fill behavior caused by a worn or broken lever
• Restores reliable engagement between the float/actuator and the switch
• Works as the mechanical linkage for the overflow/level sensing assembly

• Disconnect power and turn off the water supply before beginning service.
• Access typically requires removing the cabinet or control console; keep fasteners organized.
• Install the lever so it aligns with the switch actuator and float linkage; verify smooth movement after assembly.

This disk valve diverter directs wash water flow between spray arms and wash zones to restore proper circulation and cleaning performance. It replaces a worn or damaged diverter to help return consistent spray pressure and distribution. What it does:

• Routes pump water to the correct spray arm or wash zone during the wash cycle
• Helps maintain even spray pressure for effective cleaning
• Worn or broken diverter can cause poor cleaning, reduced water to a spray arm, or unusual pump noise
• Prevents bypass flow that can reduce wash performance

• One disk valve diverter as shown

• Disconnect power to the appliance and shut off the water supply before starting
• Access may require removing the tub access panel or disassembling spray arm/tub components
• Inspect surrounding seals and gaskets; replace any damaged parts to prevent leaks
• After installation, run a short cycle and check for proper water routing and leaks

Color: White. Size: 1 qt. can. Acrylic appliance paint.

Also order air vent seal

The Whirlpool push on retainer nut is an OEM replacement part responsible for securing the heating element in the dishwasher. It is located in the base of the dishwasher's tub to hold the heating element firmly in place. The push-on retainer nut keeps the heating element securely connected to the dishwasher's electrical system while allowing for easy removal and replacement when necessary.

Over time, push on retainer nuts can become loose, worn out, or damaged due to regular use, vibrations, or accidental mishandling. If a retainer nut fails, it can lead to parts becoming unstable or disconnected.

Symptoms of a bad push on retainer nut include:

• Loose or unstable dishwasher components
• Parts falling off or becoming misaligned
• Unusual noises during the wash cycle
• Difficulty in securing components within the dishwasher

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models

This is a durable pump and motor assembly for dishwashers. The purpose of the pump and motor is to pump water that goes through the spray arms when the dishwasher moves through a cycle. If the pump and motor assembly isn't working correctly, it could lead to dishes that are dirty after a cycle is complete. Other signs of a bad pump and motor include pooling water after a cycle and whining noises.If the pump and motor assembly need to be replaced, make sure the dishwasher is unplugged. Use a pair of work gloves to protect the hands throughout the process. Close the water supply valve and disconnect the drain line. Replacing the pump and motor assembly may require tilting the dishwasher on its side to disassemble the components that are in the way of the replacement. Once the pump and motor have been removed, install the new parts and reassemble the dishwasher before use.Created for use with dishwashers by KitchenAid, Kenmore, and Whirlpool, this pump and motor assembly is a genuine OEM replacement part. It is sold as a single part. This component is directly sourced from the manufacturer.