Kenmore Dishwasher 665.13423K701 (66513423K701, 665 13423K701) Parts

This electronic control board is the dishwasher's brain, managing cycles and powering the pump, valve, heater, and other loads. Replacing a failed board restores normal start, wash, drain, and dry functions.

• Coordinates and times wash cycles based on user selections and sensor inputs
• Sends power to the circulation pump, drain pump, water inlet valve, and heater
• Interfaces with the user interface and monitors door/latch status
• Failure may cause: no start, cycle won't advance or ends early, no fill/drain/heat, or error codes

• Disconnect power at the breaker before servicing; verify power is off
• Access location varies by model; commonly behind the lower toe panel or inside the console
• Handle the board by the edges and observe ESD (anti-static) precautions
• Move wire connectors one at a time from the old board to the new, secure the board, and reassemble; run any required diagnostics/reset per your model's tech sheet

This heater terminal nut fastens the heating element's electrical connector to its stud, keeping the connection tight under heat and vibration. Replacing a worn or missing nut restores safe contact and consistent heating performance.

• Secures the wire/ring terminal to the heater stud for a solid electrical connection
• Helps prevent arcing, discoloration, and heat damage from a loose connection
• Signs include a loose terminal, burnt odor, or melted/charred insulation at the heater connection

• Disconnect power and allow the appliance and element to cool completely before service
• Photograph wiring for reference; remove old hardware and clean the terminal
• Inspect the ring terminal, insulators, and stud; replace any heat-damaged components
• Start threads by hand to avoid cross-threading; snug with the correct nut driver—do not overtighten

This cap is a small protective cover used on select appliances to close off an opening or fastener. Replacing a damaged or missing cap helps keep out debris and moisture while restoring a clean, finished appearance.

• Covers an exposed opening or fastener to protect internal components
• Helps keep out dust, moisture, and spills
• Restores a clean, finished look and prevents snags
• Replace if the original cap is cracked, missing, discolored, or won't stay seated

• Disconnect power and, if applicable, shut off water or gas before service
• Remove the old cap by pulling straight off or unthreading, as designed
• Align the new cap and press or thread into place without forcing
• Verify a secure fit before restoring power and connections

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This small retainer secures the flexible tine-row "comb" on the dishwasher rack. Replacing a cracked or missing clip keeps fold-down tines aligned and stable so dishes load properly and rack parts stay in place.

• Holds the flexrow comb firmly to the dishrack to support adjustable/fold-down tines
• Helps prevent the comb strip from loosening or popping off the rack
• Common symptoms: flexrow won't stay attached, tines collapse or misalign, broken or missing clip
• Restores original rack function and stability

• Disconnect power to the dishwasher for safety
• Pull the rack out and locate the flexrow comb and its retainer
• Release the old retainer's locking tabs (a small flat-blade screwdriver can help), then remove it
• Align and snap the new retainer into place; the tines move and lock as intended

This overfill control float assembly sits in the dishwasher tub and rises with the water level. It works with the float switch to shut off the inlet valve, helping prevent overfilling and potential leaks.

• Rises with the water level to engage the float switch and stop water flow
• Helps protect against tub overfill and floor leaks during the fill cycle
• Replace if the float is missing, warped, stuck, or doesn't move freely
• Symptoms can include continuous filling/overfilling, water spilling from the door, or no fill if the float is stuck in the up position

• Disconnect power and turn off the water supply before servicing
• Remove the lower rack; lift the old float straight up from the tub opening
• Clear any debris from the float well so the new float moves freely
• After reassembly, start a fill to ensure the float rises and water shuts off

This feed tube assembly channels wash water from the pump to the upper spray system. Replacing a cracked or obstructed tube helps restore upper-rack cleaning performance and can prevent leaks at the back of the tub. What it does:

• Routes water from the circulation pump to the rear manifold/upper spray system
• Helps maintain proper spray pressure for upper-rack washing
• Addresses visible cracks, broken locking tabs, or mineral buildup on the tube

• 1 feed tube assembly

• Disconnect power and shut off water to the dishwasher before servicing
• Remove racks as needed; release retaining tabs/clips and detach the tube from its connections
• Inspect and reuse existing seals/clips only if in good condition; replace worn seals
• Ensure the tube is fully seated and latched at all connection points before reassembly

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

12 Ft in length

This is the lower access panel for the appliance's base. It finishes the front opening and shields internal components, helping reduce noise and keep dust and debris away from the motor and wiring.

• Covers the lower service opening beneath the door to provide a clean, finished look
• Helps protect internal components from debris and accidental contact
• Can reduce vibration noise when properly secured
• Replace if the panel is bent, cracked, rusted, missing, or rattles/doesn't stay secured

• Disconnect power; also shut off the water supply
• Support the existing panel while removing mounting screws; retain hardware for reuse
• Position the new panel, align with mounting holes/slots, and reinstall screws—do not overtighten
• Confirm door clearance and that the panel sits flush without interference

This spray arm distributes wash water inside the dishwasher, rotating to deliver even spray coverage across the racks. Replace a cracked or clogged arm to restore consistent cleaning performance and reliable water distribution.

• Directs pressurized water through jet openings while spinning to wash dishes evenly
• Helps address symptoms such as poor cleaning results or uneven spray coverage
• Replace if the arm is cracked, warped, mineral-fouled, or no longer spins freely
• Damage or improper seating can cause the arm to strike dishes/tub and make noise

• Disconnect power to the dishwasher before servicing
• Remove rack(s) if needed; release the arm by unscrewing the retainer or pressing the locking tab (method varies by model)
• Clean debris from the mounting hub and seal surfaces before installing the new arm
• Seat fully, ensure the arm spins freely with proper clearance, then run a test cycle

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This active vent assembly controls airflow from the dishwasher during and after a cycle, releasing humid air at the right time for better drying. Replacing a faulty vent can reduce lingering moisture and steam escaping from the door.

• Regulates and directs moist air out of the tub during the dry portion of the cycle
• Closes during wash to help contain water and heat inside the dishwasher
• Helps reduce interior condensation and improve overall drying results
• Common failure symptoms: dishes not drying, moisture remaining after the cycle, steam escaping at the top of the door, or unusual noise from the vent area

• Disconnect power at the breaker before servicing; allow the unit to cool
• Access is typically through the inner door panel; retain and reuse mounting hardware as required
• Inspect and correctly seat the vent seal to prevent steam leaks
• After installation, run a test cycle to check for proper vent operation and sealing

This small retainer clip secures a light assembly or lens so it stays firmly in place during normal operation. Replacing a worn or missing clip helps prevent loose covers, rattles, and poor light positioning.

• Holds the light lens or fixture securely against its mounting surface
• Helps maintain proper alignment for consistent illumination
• Replaces broken, bent, or missing hardware
• Common fix for a loose or falling light cover or a vibrating light assembly

• Disconnect power to the appliance before servicing
• Allow hot surfaces and bulbs to cool before working near the light area
• Support the lens/fixture while removing the old clip to prevent dropping
• Ensure the new clip seats fully and the light assembly is secure before restoring power

Restore worn dishwasher racks and help prevent rust stains on dishes. This white rack repair kit covers chipped or exposed rack tines and caps bare metal to reduce corrosion and extend the useful life of your racks.

• Re-coats rusted or chipped vinyl on rack tines to help stop corrosion
• Caps exposed tips to reduce rust transfer, scratching, and snags
• Useful when tine caps are missing or the rack coating is flaking
• Common symptoms: rust on tines, stained dishes, sharp/rough tine ends

• Disconnect power and remove the rack before repair
• Clean and dry affected areas thoroughly before applying coating
• Apply in a well-ventilated area; allow full cure time before using the dishwasher
• Replace the rack if metal is severely corroded or broken