Kenmore Dishwasher 665.13632K901 (66513632K901, 665 13632K901) Parts

This bezel vent deflector covers and directs dryer exhaust while keeping the vent opening neat and protected. It restores proper airflow path and prevents clothes or lint from catching on the exhaust opening. What it does:

• Guides exhaust air from the dryer to the vent outlet for better airflow
• Protects the vent opening from snags, debris, and visible wear
• Helps reduce lint escape at the cabinet opening and keeps the area tidy
• Replaces cracked, warped, or missing vent bezel that can affect exhaust performance

• One bezel vent deflector

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access the vent area per your model's service instructions (rear or front panel removal may be required)
• Align tabs/clips and press into place; replace any broken retaining clips or screws as needed
• Clean the ductwork and lint trap before reinstalling

This durable silverware basket holds forks, knives and other utensils securely during dishwasher cycles so small items stay corralled and clean. Fits into the dishwasher rack to keep cutlery organized and prevent items from falling through. What it does:

• Holds and organizes silverware and small kitchen utensils during wash cycles
• Keeps utensils upright and separated for better cleaning and drying
• Prevents small items from slipping into the dishwasher spray area or drain
• Replaces cracked, broken or missing baskets that allow cutlery to scatter

• No tools required; remove the lower rack and set the basket into the designated rack slots
• Ensure basket snaps or rests securely and does not interfere with rack movement or spray arms
• Inspect basket for cracks or sharp edges before use; discontinue use if damaged
• Always follow the appliance manufacturer's safety and installation instructions

This left-hand door hinge supports and pivots the door so it opens smoothly and closes tight. Replace a worn hinge to correct sagging, rubbing, or doors that won't seal—improving performance and preventing damage. What it does:

• Provides the pivot point for the door on the left side
• Maintains alignment so the door sits level and latches/seals properly
• Helps the door open and close smoothly without binding
• Common symptoms: door sags or rubs, won't close fully, uneven gaps, squeaking/grinding noises, poor seal

• One left-hand door hinge

• Disconnect power; also shut off gas and/or water before servicing
• Support or remove the door before unfastening the hinge; some hinges may be under spring tension—use caution
• Transfer original hardware/shims as needed and tighten fasteners securely
• Check door alignment and gasket contact after installation; open/close several times to ensure smooth operation

• "Left-hand" is determined when facing the front of the appliance.

Right-hand door hinge that replaces a worn or damaged refrigerator door hinge to restore proper door alignment and smooth opening and closing. Helps maintain a tight seal and prevents door sag or binding. What it does:

• Supports and pivots the refrigerator door on the right-hand side for correct alignment.
• Restores smooth opening/closing and reduces rubbing or scraping at the cabinet.
• Helps re-establish a full door seal to prevent cold air loss and temperature issues.
• Addresses symptoms such as a sagging or misaligned door, noisy hinge movement, or a door that doesn't close evenly.

• Disconnect power to the appliance and remove any items from the door before starting.
• Support the door while removing hinge hardware to prevent sudden drops or damage.
• Reuse existing screws/hardware unless replacement hardware is provided; tighten securely but avoid over-torquing.
• After installation, check door alignment and gasket contact; adjust hinge position as needed to ensure proper sealing.

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

The Filter Screen is an OEM component specifically designed for Whirlpool dishwashers. Located inside the sump area, the durable mesh screen captures small food particles and debris before wash water is recirculated through cycles.

Symptoms of a bad filter screen can include clogging obscuring openings over time, degrading mesh no longer inhibiting passage, or dislodging from mounting points allowing bypass.

Causes involve the normal accumulation of soils requiring periodic cleaning. Mineral buildup may eventually cement sections together reducing effectiveness. 

Symptoms of a bad filter screen include:

• Dirty or soiled wash water unable to fully circulate  
• Filth dispersing throughout the wash cabinet interior
• Reduced cleaning and unsatisfactory dish results

This OEM Whirlpool part is also compatible with KitchenAid, Maytag, Jenn-Air, Amana, and some Kenmore dishwasher models. Replace to maintain built-in wastewater filtration protecting major components.

The Circulation Motor is an OEM part for Whirlpool dishwashers. It is responsible for pumping water through the spray arms to ensure thorough cleaning of dishes during the wash cycle. This motor helps maintain consistent water pressure and flow, crucial for effective dishwashing performance.

Over time, the circulation motor can fail due to factors such as motor wear, electrical issues, or blockages that cause the motor to overheat or become damaged. Regular use and the buildup of debris or hard water deposits can also contribute to motor failure.

Symptoms of a bad circulation motor include:

• Poor cleaning results
• Unusual noises during the wash cycle
• Water not circulating properly
• Dishwasher not completing cycles

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The OEM Electronic Control Board is an OEM replacement part for Whirlpool dishwashers. It is a circuit board that controls all of the functions of the dishwasher, including the wash cycles, water temperature, and detergent dispensing.

Causes of failure involve damage from liquid intrusion shortening circuits or component deterioration over extended use reducing precision.

Symptoms include:

• Dishwasher fails to start selected cycle
• Lights, displays or programming malfunctions
• No response from control buttons
• Dishwasher appears dead or powerless

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

The Pump and Motor Assembly is an OEM part for Whirlpool dishwashers. This part is responsible for circulating water during the wash cycle and draining water at the end of the cycle.  

Causes of a bad assembly can include blockages from debris, electrical failures, or wear and tear from regular use.  

Symptoms of a bad Pump and Motor Assembly include:

• Dishes remaining dirty after a wash cycle
• Water not draining properly from the dishwasher
• Unusual noises during operation
• Error codes related to water flow or pump performance

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: Black - Part has been changed to an Access Panel Kit - The toe panel is no longer used.

Color: Stainless

This inner door plastic is the interior panel for the appliance door that supports latch and hinge hardware and helps maintain the door seal. Replacing a cracked or damaged inner panel restores proper door fit and function. What it does:

• Supports the door assembly and secures internal components; a damaged panel often causes a loose or rattling door.
• Provides mounting points for the latch and hinge hardware; symptoms include a door that won't latch or closes unevenly.
• Helps maintain the appliance seal and thermal integrity; symptoms can include noticeable air/heat leakage or reduced performance.
• Restores the interior appearance of the door when the original plastic is cracked, warped, or broken.

• Disconnect power to the appliance before beginning work and fully open the door; support the door to prevent it from dropping when fasteners are removed.
• Remove the required screws/fasteners and lift out the inner panel carefully; wear safety gloves and eye protection if glass is present.
• Check hinge and latch alignment during reassembly; replace any damaged fasteners and avoid overtightening screws which can crack the plastic.

This replacement wheel installation leg restores mobility and stable support for appliances that use a leg-mounted rolling wheel. It provides a direct-fit restore of worn or damaged legs to help move and position the appliance safely. What it does

• Replaces a damaged or worn wheel-style leg that supports and helps roll the appliance
• Restores smooth rolling and stabilizes appliance during movement
• Helps resolve symptoms like a broken/collapsed leg, stuck wheel, or uneven appliance height
• Matches OEM form and fit for direct replacement when the original leg/wheel is worn

• One wheel installation leg

• Turn off and unplug the appliance and remove contents or shelves as needed before working underneath
• Use basic hand tools; avoid forcing components—reuse existing fasteners