Kenmore Dishwasher 665.13844K600 (66513844K600, 665 13844K600) Parts

This dispenser cover (shield) replaces the plastic trim that surrounds a refrigerator's dispenser opening, restoring a clean finished look and helping direct water or ice into your cup. Fits where the dispenser meets the cabinet face. What it does:

• Covers and protects the dispenser opening, preventing chips and cosmetic damage
• Helps guide water and ice into cups for more accurate dispensing
• Hides internal dispenser components for a finished appearance
• Can reduce direct contact with moving dispenser parts

• One dispenser cover (shield)

• Remove power to the appliance before servicing to avoid electrical or injury risk
• Typically installs by snapping into place or fastening with a few screws; keep hardware if reusing
• Inspect surrounding trim for damage and replace any broken clips or screws for a secure fit

This loose bag assembly is a direct-fit replacement designed to restore the original containment or collection function in compatible Whirlpool appliances. It provides a simple swap to fix a damaged or missing bag and keep the appliance operating as intended. What it does:

• Replaces a worn, torn, or missing bag used for containment or collection in the appliance
• Restores proper collection and helps prevent debris or material from escaping into the appliance cavity
• Helps reduce related performance issues that occur when the bag is damaged or absent
• Matches OEM form and fit for an easy, reliable replacement

• One loose bag assembly as shown

• Turn off and unplug the appliance before attempting replacement
• Remove any panels or components required to access the bag
• Install the bag in the correct orientation and secure all fasteners or clips
• Inspect surrounding seals and openings; replace any damaged parts to ensure proper operation

This adjuster is a replacement door/hinge adjustment component that restores proper door alignment and closing action for compatible appliances. It helps re-establish correct clearance and reduces rubbing, binding, or uneven gaps. What it does:

• Provides the adjustment point for proper door alignment and smooth operation
• Helps correct doors that sit unevenly, rub, or don't seal consistently
• Restores the ability to fine-tune door position after hinge or cabinet repairs
• Reduces noise and wear caused by misaligned doors or panels

• One adjuster as shown

• Turn power off and disconnect the appliance before starting any repair
• Some disassembly of the door, hinge, or trim may be required
• Keep fasteners and small parts organized; verify orientation before final tightening

For spray arm seal use WP8268340.

Color: Bisque

A flat washer used with fasteners on select top-load and front-load washer assemblies to distribute load and prevent loosening. Replaces worn or missing washers to help stabilize mounting points and reduce vibration where metal parts join. What it does:

• Provides a smooth bearing surface between a bolt or nut and the mating part
• Helps distribute clamping force to prevent damage to housings or panels
• Reduces loosening from vibration or thermal cycling
• Common fix when mounting hardware is loose, rattling, or causing leaks at joins

• Inspect mating bolt, nut, and surface for wear or damage before installing
• Use correct size and orientation; do not overtighten fasteners
• Disconnect power to the appliance and follow safety procedures when accessing internal parts
• Replace all related fasteners to ensure proper fit

This bezel vent deflector covers and directs dryer exhaust while keeping the vent opening neat and protected. It restores proper airflow path and prevents clothes or lint from catching on the exhaust opening. What it does:

• Guides exhaust air from the dryer to the vent outlet for better airflow
• Protects the vent opening from snags, debris, and visible wear
• Helps reduce lint escape at the cabinet opening and keeps the area tidy
• Replaces cracked, warped, or missing vent bezel that can affect exhaust performance

• One bezel vent deflector

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access the vent area per your model's service instructions (rear or front panel removal may be required)
• Align tabs/clips and press into place; replace any broken retaining clips or screws as needed
• Clean the ductwork and lint trap before reinstalling

This left-hand door hinge supports and pivots the door so it opens smoothly and closes tight. Replace a worn hinge to correct sagging, rubbing, or doors that won't seal—improving performance and preventing damage. What it does:

• Provides the pivot point for the door on the left side
• Maintains alignment so the door sits level and latches/seals properly
• Helps the door open and close smoothly without binding
• Common symptoms: door sags or rubs, won't close fully, uneven gaps, squeaking/grinding noises, poor seal

• One left-hand door hinge

• Disconnect power; also shut off gas and/or water before servicing
• Support or remove the door before unfastening the hinge; some hinges may be under spring tension—use caution
• Transfer original hardware/shims as needed and tighten fasteners securely
• Check door alignment and gasket contact after installation; open/close several times to ensure smooth operation

• "Left-hand" is determined when facing the front of the appliance.

Right-hand door hinge that replaces a worn or damaged refrigerator door hinge to restore proper door alignment and smooth opening and closing. Helps maintain a tight seal and prevents door sag or binding. What it does:

• Supports and pivots the refrigerator door on the right-hand side for correct alignment.
• Restores smooth opening/closing and reduces rubbing or scraping at the cabinet.
• Helps re-establish a full door seal to prevent cold air loss and temperature issues.
• Addresses symptoms such as a sagging or misaligned door, noisy hinge movement, or a door that doesn't close evenly.

• Disconnect power to the appliance and remove any items from the door before starting.
• Support the door while removing hinge hardware to prevent sudden drops or damage.
• Reuse existing screws/hardware unless replacement hardware is provided; tighten securely but avoid over-torquing.
• After installation, check door alignment and gasket contact; adjust hinge position as needed to ensure proper sealing.

The Filter Screen is an OEM component specifically designed for Whirlpool dishwashers. Located inside the sump area, the durable mesh screen captures small food particles and debris before wash water is recirculated through cycles.

Symptoms of a bad filter screen can include clogging obscuring openings over time, degrading mesh no longer inhibiting passage, or dislodging from mounting points allowing bypass.

Causes involve the normal accumulation of soils requiring periodic cleaning. Mineral buildup may eventually cement sections together reducing effectiveness. 

Symptoms of a bad filter screen include:

• Dirty or soiled wash water unable to fully circulate  
• Filth dispersing throughout the wash cabinet interior
• Reduced cleaning and unsatisfactory dish results

This OEM Whirlpool part is also compatible with KitchenAid, Maytag, Jenn-Air, Amana, and some Kenmore dishwasher models. Replace to maintain built-in wastewater filtration protecting major components.

The Dishwasher Food Chopper is an OEM part for Whirlpool dishwashers. It's designed to break down food particles that are washed off dishes during the cleaning cycle. This prevents large debris from clogging the dishwasher's drain and ensures that water remains clean throughout the cycle, enhancing the machine's cleaning efficiency. 

A malfunctioning or worn-out food chopper can lead to several problems, such as poor cleaning results due to food particles being redeposited on dishes, or even clogs that can strain the dishwasher's pump and filters. 

Symptoms of a bad Dishwasher Food Chopper include:

• Dishes coming out with food particles still on them
• The dishwasher making unusual noises indicating a struggle or blockage
• Water not draining properly, suggesting a possible clog

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Circulation Motor is an OEM part for Whirlpool dishwashers. It is responsible for pumping water through the spray arms to ensure thorough cleaning of dishes during the wash cycle. This motor helps maintain consistent water pressure and flow, crucial for effective dishwashing performance.

Over time, the circulation motor can fail due to factors such as motor wear, electrical issues, or blockages that cause the motor to overheat or become damaged. Regular use and the buildup of debris or hard water deposits can also contribute to motor failure.

Symptoms of a bad circulation motor include:

• Poor cleaning results
• Unusual noises during the wash cycle
• Water not circulating properly
• Dishwasher not completing cycles

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Control Board is an OEM part for Whirlpool dishwashers. As the central processing unit, this board regulates all cycles and component functions including wash and rinse settings, heating controls and the digital display.

Symptoms of a failed control board include:

• Inability to select or change wash/rinse options
• Cycles failing to complete through all settings
• Error codes displayed or unresponsive controls

Causes can be normal wear of electronic components over extended use. Exposure to fluctuating internal temperatures may also deteriorate electrical connections over time.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.