Kenmore Dishwasher 665.13923K011 (66513923K011, 665 13923K011) Parts

This fine screen is the small mesh filter that sits in the dishwasher sump to catch food particles and help protect the pump and wash system. It keeps debris from circulating so dishes rinse more effectively. What it does:

• Traps food and debris in the sump to prevent clogging and pump damage
• Helps maintain proper water flow for consistent wash and drain performance
• Reduces risk of food redepositing on dishes during cycles
• Commonly replaced when torn, heavily clogged, or missing

• One fine mesh sump screen

• Turn off power and disconnect the dishwasher before servicing
• Remove the lower dish rack and access the sump area to replace the screen
• Inspect surrounding seals and housing for damage while servicing
• No special tools typically required; handle mesh gently to avoid deformation

This disk valve diverter directs wash water flow between spray arms and wash zones to restore proper circulation and cleaning performance. It replaces a worn or damaged diverter to help return consistent spray pressure and distribution. What it does:

• Routes pump water to the correct spray arm or wash zone during the wash cycle
• Helps maintain even spray pressure for effective cleaning
• Worn or broken diverter can cause poor cleaning, reduced water to a spray arm, or unusual pump noise
• Prevents bypass flow that can reduce wash performance

• One disk valve diverter as shown

• Disconnect power to the appliance and shut off the water supply before starting
• Access may require removing the tub access panel or disassembling spray arm/tub components
• Inspect surrounding seals and gaskets; replace any damaged parts to prevent leaks
• After installation, run a short cycle and check for proper water routing and leaks

This plate-latch strike secures the appliance door by engaging the latch assembly so the door stays closed during operation. It replaces a worn or damaged strike to restore proper door closure and reliable operation. What it does:

• Provides a sturdy contact point for the door latch to engage and hold the door closed
• Helps prevent the door from popping open during use, which can cause cycle interruption
• Addresses symptoms like a door that won't stay latched, won't close fully, or causes the unit to stop mid-cycle
• Works as the mating strike for the existing latch assembly to ensure proper alignment

• One plate-latch strike

• Disconnect power to the appliance before beginning any repair
• Access the strike by opening the door; remove any trim or screws as needed to reach the strike mounting location
• Install replacement in the same orientation as the original and tighten fasteners securely without over-torquing
• After installation, verify the door latches smoothly and the appliance completes its normal cycle

Color: White. Size: 1 qt. can. Acrylic appliance paint.

This spacer fits between tank components to maintain proper spacing and alignment, helping reduce vibration and wear. Use this genuine replacement to restore correct clearances and improve stability in the appliance's tank assembly. What it does:

• Positions and separates tank parts to maintain correct alignment during operation
• Helps reduce noise and vibration caused by misaligned components
• Prevents metal-to-metal contact that can cause premature wear or damage
• Restores factory clearances after service or replacement of tank parts

• One spacer

• Designed for direct replacement; use the OEM mounting location and orientation
• Disconnect power and water (if applicable) before beginning repair
• If fasteners or surrounding components are worn or damaged, replace them to ensure a secure fit

This replacement lower dishrack restores the main loading surface in your dishwasher so dishes sit securely and spray reaches them for better cleaning. It replaces a cracked, rusted, or misshapen rack to help protect dishes and keep loading organized. What it does

• Provides a stable platform to hold plates, bowls and cookware during wash cycles
• Maintains correct spacing so spray arms can reach all items for effective cleaning
• Replaces bent or rusted rack wires that can snag or chip dishes
• Helps keep utensil baskets and rollers aligned for smooth rack movement

• One lower dishrack

• Remove dishwasher racks and disconnect water/electric only if required by your model; most rack swaps are simple hand installs
• Inspect and transfer any rollers, clips, or utensil baskets from the old rack to the new one if needed
• Handle carefully to avoid wire ends that may be sharp; wear gloves if helpful
• If rails or rollers are damaged, replace those parts as well for proper rack operation

The Thermostat Housing is an OEM part for Whirlpool dishwashers. It encases the thermostat responsible for accurately monitoring water temperatures throughout cleaning cycles. 

Symptoms of a faulty housing include:

• Inconsistent or improper water heating  
• Delayed or incomplete cycles from temperature control issues
• Error codes or failure detection by the control board

Causes may involve cracks allowing steam penetration, loose mounting points compromising seals, or damaged seals leaking interior thermostat components. 

This OEM replacement fits Whirlpool, KitchenAid, Jenn-Air, and some Kenmore models as well.

This replacement door handle restores a secure grip and clean appearance to the refrigerator or freezer door. Built to match OEM fit and finish so the door opens and closes smoothly. What it does

• Provides a solid gripping surface for opening and closing the refrigerator or freezer door
• Replaces a cracked, loose, or broken handle that causes difficult or unsafe operation
• Helps maintain the door alignment and user control when pulling the door
• Matches the OEM contour and mounting points for an accurate fit

• Requires basic hand tools; access to inner door trim may be needed for removal/installation
• Disconnect power and empty door pockets if needed to avoid injury or damage
• If mounting hardware is missing or worn, replace with manufacturer-recommended fasteners

This replacement shield is a small protective cover that helps guard nearby components from heat, moisture, or debris, reducing wear and preventing damage for reliable appliance operation. What it does:

• Covers and protects adjacent parts from heat, moisture, grease, or debris
• Helps maintain proper airflow or clearance around components where fitted
• Prevents rubbing, chafing, and minor impact damage to wiring or panels
• Can reduce noise caused by loose or exposed parts contacting other surfaces

• One replacement shield

• Disconnect power (unplug or shut off breaker) before inspecting or replacing the shield
• Follow OEM disassembly steps for access; handle mounting tabs carefully to avoid breakage
• Use appropriate fasteners; replace any damaged clips or screws with OEM equivalents