Kenmore Dishwasher 665.15625692 (66515625692, 665 15625692) Parts

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

Restore smooth loading and secure placement for your dishes with this replacement dishrack. Replacing a bent, rusty, or damaged rack helps keep items upright, improves spray coverage, and prevents flaking or broken tines from contaminating the wash. What it does

• Holds and organizes dishes, bowls, and cookware during the wash cycle
• Slides on the rail system for easy loading and unloading
• Helps maintain proper spray coverage and drainage for effective cleaning
• Common symptoms of failure: rusted or broken tines, peeling rack coating, rack wobbling or derailing, poor rolling, items tipping over

What's included

• 1 dishrack

Install notes

• Disconnect power and shut off water; open the door and fully extend the rack
• Remove rail stop clips/end caps as applicable and slide out the old rack; wear gloves to avoid cuts from sharp edges or rust
• Transfer any reusable accessories (silverware basket, clips, holders) from the old rack if needed
• Slide the new rack onto the rails, reinstall the stops, and verify it glides smoothly before running a cycle

Screw for wash impeller.

This pump outlet directs drained water from the washer's pump housing into the drain hose, helping the appliance remove wastewater efficiently. Replacing a damaged outlet restores proper drainage and reduces leaks. What it does:

• Channels water from the pump to the drain hose to enable normal draining
• Seals the pump discharge to prevent leaks at the pump exit
• A cracked or clogged outlet can cause slow or no-drain symptoms, leaks under the washer, or water pooling
• Works with the pump assembly to maintain correct water flow during drain cycles

• One pump outlet and the part shown as item 13 in the OEM diagram

• Disconnect power (unplug or switch off breaker) before beginning service
• Turn off and disconnect water lines if needed and place towels to catch residual water
• Inspect and replace any worn clamps, gaskets, or seals when installing the outlet
• Recheck connections and test a short drain cycle after installation to confirm no leaks

Color: Black. For white use 3374712. For almond use 3374713

This heater support secures the dryer heater assembly so it stays aligned and stable during operation, helping maintain proper airflow and heating performance. It's a direct-fit replacement designed to restore correct heater positioning. What it does:

• Holds the heater assembly in place to prevent shifting or contact with other components
• Helps maintain proper airflow path for efficient drying and consistent heat
• Reduces rattling, rubbing, or intermittent heating caused by a loose heater
• Works with the heater housing and mounting points to keep electrical and thermal parts separated

• Refer to the dryer's service manual or parts diagram for correct placement and orientation
• Disconnect power before starting work to avoid electrical shock
• Inspect surrounding clips, screws, and the heater assembly; replace any damaged fasteners

This O-ring is a small rubber replacement seal that helps stop water leaks where two components meet. It restores a tight seal to reduce drips and prevent water damage from worn or cracked seals. What it does:

• Provides a compression seal between mating parts to prevent leaks
• Commonly replaced when visible cracking, flattening, or hardening occurs
• Helps eliminate steady drips or pooling of water near the seal area
• Restores proper sealing after disassembly for service or part replacement

• Disconnect power and shut off the water supply before servicing
• Remove surrounding components carefully to avoid damaging the seal seat
• Inspect the mating surfaces for debris or damage; clean before installing new O-ring
• Lubricate with a compatible, appliance-safe lubricant; do not use petroleum-based products unless specified

This premium dispenser cam engages the dispenser mechanism to control door/lever movement and ensure reliable dispense actions. It replaces a worn cam to restore proper dispenser function and consistent operation. What it does:

• Rotates and times the dispenser lever/door so the dispenser opens and closes correctly
• Transfers motion from the actuator to the dispenser linkage or switch
• Commonly used when the dispenser lever feels loose, doesn't return, or dispensing is intermittent
• Helps stop unwanted continuous dispensing caused by a worn cam surface

• Disconnect power (and water supply if applicable) before starting work
• Access the dispenser assembly; removal of the dispenser bezel or control housing may be required
• Handle small plastic parts carefully to avoid breaking tabs; align cam on shaft before reassembly
• Test dispenser operation after reassembly to ensure correct movement and sealing

Size: 8-32 x 1/4 inch.

This small cupshelf is the replacement door shelf insert that restores secure storage for cups, glasses and small items in your refrigerator door. It helps organize the door and prevents items from shifting or falling. What it does:

• Replaces a cracked, broken or missing small cupshelf to restore door storage capacity
• Supports cups, small glasses and lightweight containers on the refrigerator door
• Helps keep items organized and prevents sliding when the door opens or closes
• Matches OEM fit and mounting points when used as the specified replacement part

• One small cupshelf

• Remove items from the door and lift out the old shelf; align tabs and snap the new shelf into the existing door mounts
• No special tools are typically required; handle carefully to avoid damaging door trim or mounting tabs
• Always follow refrigerator power/safety guidance from the manufacturer when working near controls or lights

Size: 8-32.