Kenmore Dishwasher 665.15914001 (66515914001, 665 15914001) Parts

This thermostat bracket holds the oven or range thermostat securely in place, ensuring accurate temperature sensing and stable oven performance. Replaces a worn or broken bracket to restore proper thermostat positioning. What it does:

• Secures the thermostat assembly to the oven/range interior so the thermostat bulb or probe senses temperature correctly
• Prevents the thermostat from shifting or contacting heating elements
• Commonly replaced when the bracket is cracked, bent, or missing and causes temperature or control issues
• Helps reduce temperature inconsistencies caused by a loose or damaged mounting

• Disconnect power to the appliance before servicing to avoid electrical shock or injury
• Handle the thermostat and sensor bulb carefully; avoid kinks or direct pressure on sensing elements
• Basic hand tools are typically required; verify part alignment before tightening fasteners

This push-in retainer secures panels, trim or light-weight components inside the appliance to prevent vibration and movement during operation. It's a small, low-profile fastener that snaps into a pre-drilled hole for a clean, tool-free hold. What it does:

• Holds interior trim, access panels or wiring looms in place to reduce rattles and movement
• Replaces worn or broken plastic retainers that no longer grip securely
• Helps maintain proper alignment of lightweight components for reliable operation
• Can prevent loose parts from contacting moving components

• Disconnect power to the appliance before starting any work
• Access the area and remove any surrounding trim or panels as needed
• Align retainer with the hole and push straight in until it snaps or seats flush
• Inspect fit after installation; replace if damaged or does not secure properly

This loose bag assembly is a direct-fit replacement designed to restore the original containment or collection function in compatible Whirlpool appliances. It provides a simple swap to fix a damaged or missing bag and keep the appliance operating as intended. What it does:

• Replaces a worn, torn, or missing bag used for containment or collection in the appliance
• Restores proper collection and helps prevent debris or material from escaping into the appliance cavity
• Helps reduce related performance issues that occur when the bag is damaged or absent
• Matches OEM form and fit for an easy, reliable replacement

• One loose bag assembly as shown

• Turn off and unplug the appliance before attempting replacement
• Remove any panels or components required to access the bag
• Install the bag in the correct orientation and secure all fasteners or clips
• Inspect surrounding seals and openings; replace any damaged parts to ensure proper operation

This silverware basket replaces a cracked, broken, or missing utensil holder to keep forks, knives and spoons organized during the wash cycle. It fits into the dishwasher's lower rack and helps maintain cleaning efficiency. What it does

• Holds and separates silverware and small utensils so water and detergent can reach each piece
• Prevents nesting and keeps items upright for better cleaning and drying
• Secures loose items during the wash to avoid damage to dishes or the dishwasher
• Works with standard lower-rack mounting locations on compatible dishwashers

• One silverware basket

• Installs in the lower dishwasher rack; no tools required for typical replacements
• Position tines or compartments so utensils sit upright and do not block spray arms
• Do not overload the basket; bent or damaged tines may affect fit and function

This rinse aid sensor detects the presence/level of rinse aid and signals the dishwasher control so the dispenser and cycle logic respond correctly. Replaces a failed sensor to restore proper rinse-aid detection. What it does

• Acts as a reed-style sensor that notifies the control when rinse aid is present
• Helps the dispenser and control board make rinse-aid–related decisions
• Commonly replaced when rinse-aid indicators fail or rinse-aid detection errors occur
• Small, low-voltage sensing device used in the dishwasher dispenser area

• One rinse aid sensor (reed switch)

• Disconnect power to the appliance before starting any service
• Access may require removing the door inner panel or dispenser assembly; follow the service manual
• Handle gently and avoid bending the sensor leads; ensure secure electrical connections

The Door Hinge (RH) is an OEM replacement part for Whirlpool dishwashers. This hinge is installed on the right-hand side of the dishwasher door, allowing it to open and close smoothly while maintaining the proper tension and alignment. The hinge plays a crucial role in ensuring the door seals securely during operation, preventing leaks and enabling efficient cleaning performance.

Common causes include regular use leading to wear and tear, accidental impacts, or exposure to moisture, which can contribute to rust or corrosion.

Symptoms of a bad door hinge include:

• The dishwasher door not closing completely
• Difficulty opening or closing the door
• A sagging or misaligned door
• Unusual noises when moving the door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Circulation Motor is an OEM part for Whirlpool dishwashers. It is responsible for pumping water through the spray arms to ensure thorough cleaning of dishes during the wash cycle. This motor helps maintain consistent water pressure and flow, crucial for effective dishwashing performance.

Over time, the circulation motor can fail due to factors such as motor wear, electrical issues, or blockages that cause the motor to overheat or become damaged. Regular use and the buildup of debris or hard water deposits can also contribute to motor failure.

Symptoms of a bad circulation motor include:

• Poor cleaning results
• Unusual noises during the wash cycle
• Water not circulating properly
• Dishwasher not completing cycles

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Detergent Dispenser Assembly is an OEM part for Whirlpool dishwashers, designed to store and release detergent and rinse aid at the appropriate times during the wash cycle. This component ensures that your dishes are cleaned efficiently by dispensing the correct amount of detergent for optimal washing performance. 

Causes of a malfunctioning dispenser can include mechanical failure of the latch or spring mechanism, clogging due to detergent buildup, or electrical issues preventing the dispenser from operating correctly.

Symptoms of a bad Detergent Dispenser Assembly include:

• Detergent not being dispensed correctly, leading to poorly cleaned dishes.
• The dispenser door not opening during the cycle or failing to latch properly before starting.
• Leakage of detergent from the dispenser, indicating a seal failure.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: Black - Part has been changed to an Access Panel Kit - The toe panel is no longer used.

This pump sump screen filters lint, debris and small objects from wash water before it reaches the drain pump, helping prevent clogs and pump damage. Replace a cracked or clogged screen to restore proper draining. What it does:

• Captures lint, coins, hair and small debris before the drain pump
• Helps prevent pump blockages that cause poor draining or standing water
• Reduces wear on the drain pump by stopping larger debris
• Improves overall drain performance when the existing screen is damaged or clogged

• Disconnect power and water before accessing the pump area
• Remove the washer access panel or cabinet per your model's service instructions to reach the sump
• Inspect and clean surrounding areas and the pump inlet when replacing the screen

A small replacement retainer that secures the FlexRow assembly so the component stays aligned and stable during use. Replacing a worn or broken retainer restores proper positioning and reduces movement. What it does:

• Holds the FlexRow assembly in place to prevent shifting or sagging
• Helps maintain correct alignment for even operation
• Stops clicking, rubbing, or intermittent contact caused by a loose assembly
• Prevents additional wear on adjacent clips or mounts

• Disconnect power to the appliance before beginning any repair
• Removal usually requires releasing adjacent clips or fasteners; basic hand tools may be needed
• Inspect surrounding parts and replace any damaged clips or mounts for a secure fit

This dual positioner assembly helps align and hold the control shaft/knob mechanism so selections register correctly and controls operate smoothly. It replaces a worn or broken positioner to restore reliable selector alignment. What it does:

• Secures and centers the control shaft/knob so detents register properly
• Prevents loose or wandering knobs and helps ensure accurate cycle selection
• Commonly replaced when knobs feel sloppy, skip positions, or controls don't stay set
• Works with the control panel mounting to stabilize selector movement

• Disconnect power to the appliance before starting any work
• Remove the control panel or console to access the positioner per your model's service instructions
• Handle plastic tabs and mounting points carefully to avoid breakage during removal/installation
• Test control function after reassembly to confirm correct alignment and operation

This inlet water bezel is the trim piece that fits around the washer's water inlet to provide a finished opening and support the inlet connection. It restores appearance and helps position the inlet area for a proper hose fit. What it does:

• Covers and finishes the water inlet opening on the cabinet for a clean appearance
• Helps hold and align the inlet connection and hose to reduce stress on the valve
• Prevents direct contact between the inlet hose/valve and the cabinet edge
• Commonly replaced when the inlet trim is cracked, broken, or worn

• Disconnect power and shut off the water supply before starting
• Remove the appropriate access panel or control console to reach the inlet area
• Handle the bezel carefully to avoid scratching painted surfaces during install
• Re-check inlet hose routing and tighten connections; test for leaks after restoring power/water