Kenmore Dishwasher 665.16919000 (66516919000, 665 16919000) Parts

This inlet fill hose directs incoming water from the household supply to the washer's tub or dispenser so the appliance fills properly. Replaces a damaged, cracked, or leaking fill hose to restore normal water flow. What it does:

• Carries water from the home supply to the washer fill valve and dispenser
• Helps the washer fill to the correct level for cycles
• Commonly replaced when you see leaks, visible cracks, or reduced fill flow
• Prevents water damage from split or worn hoses

• Disconnect power and shut off the water supply before servicing
• Inspect hose fittings and clamps; replace worn clamps and tighten securely
• Avoid sharp bends or kinks when routing the hose
• After installation, turn on water and check all connections for leaks before use

This folddown pivot is the lower hinge that lets a folddown door or panel rotate smoothly and hold position, restoring proper movement and alignment. It replaces a worn or broken lower pivot so the door or panel opens and closes correctly. What it does:

• Acts as the lower hinge point for a folddown door or panel, allowing controlled pivoting motion
• Replaces a worn, cracked, or broken pivot that causes sticking or sagging
• Helps the door/panel stay aligned and close securely instead of dropping or binding
• Commonly used when the folddown component wobbles or will not stay in the open or closed position

• Disconnect power and remove any attached panels or shelves before replacing
• Support the door/panel during removal and installation to avoid damage or injury
• Reuse OEM fasteners if undamaged or replace with equivalent hardware; ensure proper alignment during installation
• Test movement several times after installation to ensure smooth operation and secure fit

For complete door balance link kit order 8194001

This thermostat bracket holds the oven or range thermostat securely in place, ensuring accurate temperature sensing and stable oven performance. Replaces a worn or broken bracket to restore proper thermostat positioning. What it does:

• Secures the thermostat assembly to the oven/range interior so the thermostat bulb or probe senses temperature correctly
• Prevents the thermostat from shifting or contacting heating elements
• Commonly replaced when the bracket is cracked, bent, or missing and causes temperature or control issues
• Helps reduce temperature inconsistencies caused by a loose or damaged mounting

• Disconnect power to the appliance before servicing to avoid electrical shock or injury
• Handle the thermostat and sensor bulb carefully; avoid kinks or direct pressure on sensing elements
• Basic hand tools are typically required; verify part alignment before tightening fasteners

This loose bag assembly is a direct-fit replacement designed to restore the original containment or collection function in compatible Whirlpool appliances. It provides a simple swap to fix a damaged or missing bag and keep the appliance operating as intended. What it does:

• Replaces a worn, torn, or missing bag used for containment or collection in the appliance
• Restores proper collection and helps prevent debris or material from escaping into the appliance cavity
• Helps reduce related performance issues that occur when the bag is damaged or absent
• Matches OEM form and fit for an easy, reliable replacement

• One loose bag assembly as shown

• Turn off and unplug the appliance before attempting replacement
• Remove any panels or components required to access the bag
• Install the bag in the correct orientation and secure all fasteners or clips
• Inspect surrounding seals and openings; replace any damaged parts to ensure proper operation

This silverware basket replaces a cracked, broken, or missing utensil holder to keep forks, knives and spoons organized during the wash cycle. It fits into the dishwasher's lower rack and helps maintain cleaning efficiency. What it does

• Holds and separates silverware and small utensils so water and detergent can reach each piece
• Prevents nesting and keeps items upright for better cleaning and drying
• Secures loose items during the wash to avoid damage to dishes or the dishwasher
• Works with standard lower-rack mounting locations on compatible dishwashers

• One silverware basket

• Installs in the lower dishwasher rack; no tools required for typical replacements
• Position tines or compartments so utensils sit upright and do not block spray arms
• Do not overload the basket; bent or damaged tines may affect fit and function

This rinse aid sensor detects the presence/level of rinse aid and signals the dishwasher control so the dispenser and cycle logic respond correctly. Replaces a failed sensor to restore proper rinse-aid detection. What it does

• Acts as a reed-style sensor that notifies the control when rinse aid is present
• Helps the dispenser and control board make rinse-aid–related decisions
• Commonly replaced when rinse-aid indicators fail or rinse-aid detection errors occur
• Small, low-voltage sensing device used in the dishwasher dispenser area

• One rinse aid sensor (reed switch)

• Disconnect power to the appliance before starting any service
• Access may require removing the door inner panel or dispenser assembly; follow the service manual
• Handle gently and avoid bending the sensor leads; ensure secure electrical connections

A flat washer used with fasteners on select top-load and front-load washer assemblies to distribute load and prevent loosening. Replaces worn or missing washers to help stabilize mounting points and reduce vibration where metal parts join. What it does:

• Provides a smooth bearing surface between a bolt or nut and the mating part
• Helps distribute clamping force to prevent damage to housings or panels
• Reduces loosening from vibration or thermal cycling
• Common fix when mounting hardware is loose, rattling, or causing leaks at joins

• Inspect mating bolt, nut, and surface for wear or damage before installing
• Use correct size and orientation; do not overtighten fasteners
• Disconnect power to the appliance and follow safety procedures when accessing internal parts
• Replace all related fasteners to ensure proper fit

The Door Hinge (RH) is an OEM replacement part for Whirlpool dishwashers. This hinge is installed on the right-hand side of the dishwasher door, allowing it to open and close smoothly while maintaining the proper tension and alignment. The hinge plays a crucial role in ensuring the door seals securely during operation, preventing leaks and enabling efficient cleaning performance.

Common causes include regular use leading to wear and tear, accidental impacts, or exposure to moisture, which can contribute to rust or corrosion.

Symptoms of a bad door hinge include:

• The dishwasher door not closing completely
• Difficulty opening or closing the door
• A sagging or misaligned door
• Unusual noises when moving the door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Circulation Motor is an OEM part for Whirlpool dishwashers. It is responsible for pumping water through the spray arms to ensure thorough cleaning of dishes during the wash cycle. This motor helps maintain consistent water pressure and flow, crucial for effective dishwashing performance.

Over time, the circulation motor can fail due to factors such as motor wear, electrical issues, or blockages that cause the motor to overheat or become damaged. Regular use and the buildup of debris or hard water deposits can also contribute to motor failure.

Symptoms of a bad circulation motor include:

• Poor cleaning results
• Unusual noises during the wash cycle
• Water not circulating properly
• Dishwasher not completing cycles

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Detergent Dispenser Assembly is an OEM part for Whirlpool dishwashers, designed to store and release detergent and rinse aid at the appropriate times during the wash cycle. This component ensures that your dishes are cleaned efficiently by dispensing the correct amount of detergent for optimal washing performance. 

Causes of a malfunctioning dispenser can include mechanical failure of the latch or spring mechanism, clogging due to detergent buildup, or electrical issues preventing the dispenser from operating correctly.

Symptoms of a bad Detergent Dispenser Assembly include:

• Detergent not being dispensed correctly, leading to poorly cleaned dishes.
• The dispenser door not opening during the cycle or failing to latch properly before starting.
• Leakage of detergent from the dispenser, indicating a seal failure.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: Black - Part has been changed to an Access Panel Kit - The toe panel is no longer used.

This pump sump screen filters lint, debris and small objects from wash water before it reaches the drain pump, helping prevent clogs and pump damage. Replace a cracked or clogged screen to restore proper draining. What it does:

• Captures lint, coins, hair and small debris before the drain pump
• Helps prevent pump blockages that cause poor draining or standing water
• Reduces wear on the drain pump by stopping larger debris
• Improves overall drain performance when the existing screen is damaged or clogged

• Disconnect power and water before accessing the pump area
• Remove the washer access panel or cabinet per your model's service instructions to reach the sump
• Inspect and clean surrounding areas and the pump inlet when replacing the screen