Kenmore Dishwasher 665.1765191 (6651765191, 665 1765191) Parts

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

Included with nut.

This fill and drain hose assembly connects a portable dishwasher to a sink faucet, delivering incoming water and routing wastewater back to the sink. Replacing a worn assembly restores a secure connection and helps prevent leaks during operation.

• Integrates inlet and drain hoses with a faucet coupler for quick, tool-free hookup
• Supplies water to the dishwasher and returns drain water to the sink
• Can address no fill or no drain symptoms caused by a damaged or obstructed hose/coupler

• Safety first: Unplug the dishwasher and turn off water before servicing
• Expect residual water; place towels/pan and relieve line pressure
• Ensure a compatible faucet adapter is installed; attach the coupler fully and verify a good seal
• Route hoses without kinks, secure the drain end to the sink, and check for leaks on first run

This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:

• Thread-forming Type AB design engages thin metal or plastic components
• Secures panels, brackets, trim, or covers to reduce looseness and vibration
• Replaces missing, stripped, or corroded fasteners
• Helps maintain alignment for proper operation and reduced noise

• One screw

• Disconnect power before servicing; shut off water supply if working near water lines
• Use the correct driver for the screw head; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking plastic
• Repair damaged holes or replace worn clips/inserts before installing the new screw

• Size: #8-18 x 5/8 in (length 0.625 in)
• Thread type: Type AB, thread-forming

This dishwasher door spring restores proper counterbalance so the door opens smoothly and doesn't drop. The premium version provides the factory-specified tension used on select models for consistent, controlled door movement.

• Counterbalances the door for smooth opening and closing
• Helps prevent the door from slamming open or feeling heavy
• Supports stable, mid-position hold when springs are intact and matched
• Common signs of failure: door drops quickly, is hard to lift, or won't stay in position

• Disconnect power and water; remove the toe kick/access panel to reach the springs
• Note which frame/hinge holes the old spring used and install the new spring in the same positions to match tension
• Use pliers to relieve tension safely; if your model uses two springs, replace both for balanced operation
• Wear gloves and eye protection; keep hands clear of moving hinges

This hose clamp secures a flexible hose to its fitting to help prevent leaks and hose blow-offs during operation. Replace a rusted, stripped, or distorted clamp to restore a tight, reliable seal at the connection point.

• Applies clamping force around a hose to hold it on a barb or stub fitting
• Commonly used on washer drain and tub-to-pump hose connections
• Helps stop drips at the joint and prevents the hose from slipping off
• Typical failure signs: leaking at the connection, clamp won't tighten, visible rust, broken/warped band

• Unplug the appliance and turn off water supply; expect some residual water
• Seat the hose fully on the fitting; place the clamp just behind the bead/barb
• Tighten until snug and secure; do not overtighten to avoid damaging the hose
• Run a short test cycle and recheck for leaks at the connection

This upper draw bar is a door-latch linkage piece used in dishwashers. It connects the handle/actuator to the latch mechanism so the door closes securely and the door switch engages, allowing the cycle to start reliably.

• Links the door handle/actuator to the latch for positive closure
• Helps ensure the door switch is engaged so the unit will run
• Restores proper latch alignment and handle feel
• Common symptoms: door won't latch or pops open, dishwasher won't start, must push/hold door to run, loose or floppy handle

• Disconnect power at the breaker; turn off water supply if working near the inlet
• Open the door and remove inner-door screws to access the latch linkage
• Note bar orientation; transfer any clips/bushings and reuse existing hardware
• Reassemble and check latch engagement before running a cycle

Almond. Size: 13 oz. can. Acrylic appliance paint.

Color: Almond

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

This vent screen covers the dishwasher door vent, allowing steam to escape while blocking food particles and debris. Replacing a damaged or missing screen helps maintain proper airflow and can reduce moisture and odors around the vent area.

• Screens the door vent to keep debris out of the vent duct and fan path
• Maintains airflow for venting steam during the dry cycle
• A clogged, cracked, or missing screen may lead to moisture at the vent, odors, or reduced drying performance
• Replace if warped, broken, or lost during service

• Disconnect power to the dishwasher at the breaker before servicing
• Open the door and remove inner-door screws to access the vent assembly
• Remove the old screen, seat the new screen fully and evenly, then reassemble without overtightening
• Run a short cycle and check the vent area for proper airflow and moisture

Screw: 8-16 x 3/8 inch.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening

Size: 8-18 x 1/2 inch.

This wet agent dispenser replaces the washer's liquid fabric softener dispenser to restore proper dispensing during the rinse cycle. It helps keep softener contained until the machine is ready to release it, improving rinse-time performance. What it does:

• Holds and releases liquid fabric softener (wet agent) into the rinse cycle
• Ensures softener is delivered at the correct time for even distribution
• Stops leaking or premature release when the dispenser housing is intact
• Commonly replaced when the dispenser cracks, clogs, or fails to dispense

• Disconnect power to the appliance before starting any repairs
• Access method varies by model; remove dispenser drawer or top panel per your model's service instructions
• Inspect surrounding seals and clips; replace if damaged to prevent leaks