Kenmore Range 790.36932902 (79036932902, 790 36932902) Parts

This wiring harness routes power and signals between a refrigerator's control board and major components, restoring reliable electrical connections for proper operation. Use it when connectors are damaged or wiring is worn. What it does:

• Carries power and control signals between the main control and components
• Replaces burned, frayed, or broken wire runs that cause intermittent or no component operation
• Restores secure connector interfaces to fix flickering lights, non-running fans, or no cooling symptoms
• Preserves correct wiring routing to prevent shorts and maintain safe operation

• One wiring harness assembly as shown

• Always disconnect power to the appliance before starting work
• Handle connectors gently; match keyed plugs and secure all mating clips
• Route harness along original paths and secure with existing clips or ties to avoid pinching
• Replace any damaged connectors or terminals to ensure a reliable connection

This retainer is a small mounting clip that secures interior components so they stay in place and operate quietly. Replacing a worn or broken retainer restores proper fit and prevents parts from shifting or rattling. What it does:

• Secures shelves, panels or trim to the appliance cabinet to maintain correct alignment
• Prevents interior parts from shifting, rubbing or producing vibration noise
• Helps keep seals and trim seated properly to maintain a tight fit
• Commonly replaced when clips are cracked, missing or fail to hold components

• One retainer clip as pictured

• Disconnect power before servicing to avoid shock or injury
• Remove only the panels or shelves necessary to access the damaged retainer
• Install clip in the original orientation; retained component sits flush and is secure
• Use basic hand tools as needed

This replacement control panel restores the oven/stove console appearance and provides the front surface for the keypad and display, helping you use controls safely and clearly. It's a direct-fit exterior panel used where the factory front panel is cracked, scratched, or worn. What it does:

• Replaces the appliance's worn or damaged console front so buttons and display have a solid mounting surface
• Restores a clean, legible surface for touch or push-button operation
• Helps stop further cosmetic damage that can interfere with button visibility
• Addresses symptoms like cracked or chipped front surface, peeling finish, or a loose console face

• One control panel (console front) as shown

• Always disconnect power at the breaker or unplug the appliance before starting repairs
• Remove any trim pieces or screws holding the console in place; handle glass or painted surfaces carefully to avoid scratches
• Reattach all connectors and fasteners as removed; confirm proper alignment before tightening

This decorative trim piece restores the finished appearance on the appliance door or control area and covers the mounting edges for a clean, factory look. Replaces a scratched, dented, or missing trim to improve appearance. What it does:

• Covers and protects the edge of the door or control opening to keep a finished appearance
• Hides fasteners and gaps for a smoother exterior surface
• Prevents dirt and moisture from collecting in the trim gap
• Restores original aesthetics after damage or during panel replacement

• One decorative trim piece

• Install with basic hand tools; align trim over mounting area before fastening
• Do not force or bend trim; inspect adjacent mounting tabs for damage
• Disconnect power to the appliance if installation requires removing electrical panels or access behind the trim
• Replace with OEM-specified fasteners for a secure fit

This mounting bracket secures internal panels or components to the appliance frame, restoring stable support and alignment for proper operation. Use when a bracket is bent, broken or missing to reduce rattling and keep parts positioned correctly. What it does:

• Anchors panels or components to the cabinet/frame to prevent movement and vibration
• Restores proper alignment of doors, panels or internal assemblies
• Stops rattling or buzzing caused by loose or damaged support hardware
• Helps maintain safe clearance between parts and wiring or moving components

• Disconnect power to the appliance before starting any repair
• Basic hand tools typically required; follow OEM instructions for correct fastener locations
• Inspect adjacent fasteners and mounting surfaces; replace any damaged screws or clips
• If bracket is corroded or severely deformed, replace rather than re-bend to ensure proper fit

This control panel assembly replaces the console that houses the oven/range user interface and display, restoring full control and clear status readouts. It's a direct-fit console part used to operate settings and view oven feedback. What it does:

• Provides the front console with buttons/touch controls and display for selecting cook modes and temperatures
• Restores readable display and functional control buttons when the original panel is cracked, unresponsive, or cosmetically damaged
• Enables the oven/range to accept user inputs and show status, timers, and error codes
• Helps resolve issues like unresponsive keys, missing characters on the display, or a damaged control surface

• One control panel assembly (console)

• Disconnect power at the breaker or unplug the appliance before starting work
• Handle the panel carefully to avoid scratching glass or bending plastic trim
• Typical installation requires removing back or front console screws and electrical connector(s); retain all fasteners