Kenmore Wall Oven 790.47772400 (79047772400, 790 47772400) Parts

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation

This harness assembly is the appliance wiring connector bundle that carries power and signals between controls and components, restoring proper electrical connections for normal operation. What it does:

• Routes power and control signals between the control board and key components
• Replaces damaged, burned, or loose wiring that can cause intermittent operation
• Helps resolve symptoms like unresponsive controls, failure to start, or component loss of power
• Restores factory wiring layout and connector fit for reliable connections

• Disconnect power before starting; confirm power is off at the breaker
• Compare connectors and wire colors to the old harness before removal
• Route and secure harness to avoid heat or pinch points; use existing clips/mounts

This handle mounting screw is an authentic OEM replacement part sourced directly from the manufacturer for use with oven handles. The oven handle attaches to the oven door with two of these screws. If the washer that goes with the screw is loose or missing, the screw will become loose, and the handle may break away from the door. If this occurs, the door will be difficult to open when not in use and nearly impossible to open when hot. If the mounting screw is loose or missing, the screw should be replaced immediately. Note that the washer needed for the screw is not included and should be purchased separately.Make sure the oven is not hot before replacing the door handle mounting screw. To start, disconnect the power from the oven. Remove the screw and washer from the handle if it is loose and install a new handle mounting screw with a new washer. Tighten the screw until it is flush with the door. Repeat for the remaining screw if necessary.This handle mounting screw is a heavy-duty black metal screw that is sold individually. It is designed for use on ovens manufactured by Frigidaire.

This element hanger support secures a cooktop surface heating element to the range and keeps the element aligned for reliable contact and stable cooking. Replaces a worn or bent bracket to restore proper element positioning. What it does:

• Holds the surface heating element in the correct position under the cooktop
• Stabilizes the element to maintain solid electrical contact and even heating
• Helps prevent element wobble, arcing, or intermittent power to the burner
• Fits where the element connects to the terminal/anchor point on the cooktop

• 1 element hanger support bracket

• Disconnect power to the appliance before attempting any service
• Remove the cooktop or element as required to access the hanger; follow OEM disassembly steps
• Inspect element terminals and surrounding parts for damage while replacing the bracket

This white replacement handle kit restores a refrigerator door's grip and appearance after damage or wear. Designed to match original mounting locations, it provides a clean, finished look and lets you open the door safely and easily. What it does:

• Replaces a cracked, broken or faded door handle to restore safe, reliable gripping and door operation
• Secures to the existing handle bosses or mounting points for a factory-fit appearance
• Prevents further stress on the door edge and reduces the risk of accidental drops or slippage
• Matches original color and finish for a consistent look with the appliance

• One white handle and required mounting hardware

• High-level task — usually requires only basic hand tools (screwdriver); follow OEM instructions
• Remove power or keep children away during replacement to avoid pinching; no wiring involved
• Do not overtighten fasteners; snug mounting prevents damage and ensures proper fit
• Inspect and replace damaged mounting bosses or inserts before installing the handle

Specs: 8 x 0.750

This trim piece is a decorative replacement that restores the finished appearance and edge protection on your appliance. It helps cover gaps and worn edges for a clean, factory look. What it does:

• Covers and protects exposed edges and seams on the appliance exterior
• Restores the original finished appearance where trim is cracked, scratched, or missing
• Helps keep dirt and moisture out of tight seams around panels and openings
• Matches OEM fit and mounting points for straightforward replacement

• One trim piece as shown

• Remove power to the appliance before starting work when required for access
• Usually fastens with clips or screws; retain all fasteners for reassembly
• Handle carefully to avoid scratching the finish during installation

This part has been discontinued by the manufacturer and is no longer available.