Kenmore Range 791.6412190 (7916412190, 791 6412190) Parts

Replacement handle end cap that restores a finished appearance and secures the outer end of an appliance handle. Ideal for replacing cracked, chipped, or missing end caps that affect grip or the handle's look. What it does:

• Covers and protects the exposed outer end of a handle for a clean, finished appearance
• Restores proper fit and helps prevent further damage where the handle meets the door or drawer
• Addresses symptoms like a loose, chipped, cracked, or missing end cap that affects appearance or feel

• Installation method varies by model; part may snap into place or be secured with fasteners—refer to your model's service guide
• If working on a powered appliance, disconnect power before servicing
• Use appropriate hand tools and avoid prying on surrounding trim to prevent damage

This body-side spacer installs on the cabinet side of the door or lid hardware. It sets the correct stand-off and alignment so the handle or latch feels solid and sits flush for a clean, secure fit. What it does:

• Positions and supports door/lid hardware on the cabinet/body side
• Maintains proper spacing to help prevent rubbing or scuffing of the panel
• Helps keep the handle or latch tight and aligned
• Common symptoms: loose or wobbly handle/latch, uneven alignment, visible gap or scuff marks at the mounting point

• Includes 1 body-side spacer

• Disconnect power to the appliance before servicing
• Support the handle/latch, remove the cabinet-side mounting screws, place the spacer, realign hardware, and reinstall screws snugly
• Reuse the original fasteners; avoid overtightening to prevent cracking the spacer or stripping threads
• Check door operation and alignment before finishing

This hex flange nut secures components where a broader bearing surface is needed to resist loosening and distribute load. It fits 10-32 threaded studs and is used on fastened assemblies in appliances. What it does:

• Provides a secure threaded connection for 10-32 screws and studs
• Flange spreads clamping force to reduce panel or bracket damage
• Hex shape allows tightening with a wrench for a reliable hold
• Commonly replaces worn or missing nuts that cause loose panels or rattling

• One hex flange nut

• Use the correct 10-32 screw or stud and hand-start threads to avoid cross-threading
• Tighten with an appropriately sized wrench; do not overtighten to prevent thread or part damage
• Disconnect power and follow appliance safety instructions before servicing
• Replace only like-for-like; confirm size and thread match your application

Specs: 8 - 18 x 0.500

The Lens is an OEM component for Frigidaire freezers. It acts as a transparent cover and protective barrier for the freezer compartment lights. Crafted for durability and clarity, the lens avoids frost and minimizes condensation while allowing visibility inside the freezer.

Causes of a bad lens can include deep scratches or cracks developing over time from repeated wiping or exposure to chemicals like frost removers.

Symptoms of a bad freezer lens include:

• Cloudiness, fogginess, or smears inhibiting internal visibility
• Cracks or breaks compromising the protective barrier
• Distorted views make it difficult to assess food levels
• Diffused lighting with shadows instead of a clear view

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Support for broil heating element.

This replacement door gasket creates a tight seal around the refrigerator or freezer door to help maintain consistent temperatures and reduce energy loss. Designed to match the OEM shape and restore proper sealing. What it does:

• Seals the door edge to help keep cold air in and warm air out
• Helps prevent frost buildup and reduces compressor run time when sealing properly
• Can stop drafts and eliminate wet or warm spots on door edges
• Restores the door's original fit when worn, torn, or deformed

• One door gasket

• Designed for a direct replacement; inspect mounting channel and retainer before installing
• Warm the gasket slightly for easier fitting if needed; avoid overheating
• Clean the door frame and remove old adhesive or debris for a proper seal

Size: 8-18ab x 0.5 inch.

This replacement refrigerator door handle restores a secure, easy-to-grip surface for opening and closing the door and refreshes the appliance's appearance. It installs in place of a cracked, broken or missing handle to return normal door operation. What it does:

• Replaces a damaged or missing refrigerator door handle so the door can be opened and closed safely and easily
• Provides a stable grip and improves cabinet appearance when the original is cracked, loose, or cosmetically worn
• Aligns with factory mounting points to restore proper fit and clearance
• Helps prevent further damage from using temporary grips or improvised handles

• One replacement refrigerator door handle

• Use basic hand tools; support the door while removing and installing the handle to prevent shifting
• Keep items inside the fresh food compartment secure; consider having a second person assist with large doors
• Do not overtighten fasteners — snug is sufficient to avoid stripping threads or cracking the handle
• Replace any mounting hardware that is not present or clearly worn before finishing installation