Kenmore Range 791.734891 (791734891, 791 734891) Parts

This ferrule is a small compression fitting used to secure and seal a refrigerator water line connection, helping stop leaks and maintain proper flow to the ice maker or dispenser. It's a simple replacement to restore a tight water connection. What it does:

• Secures tubing to a compression or shutoff fitting to prevent leaks at the connection
• Restores a proper seal for water supply lines feeding the ice maker or dispenser
• Commonly used when a loose, dripping, or leaking water line is present
• Helps prevent water damage from failing or corroded fittings

• One ferrule

• Turn off the water supply and relieve line pressure before servicing
• Confirm tubing is cut square, fully inserted, and the ferrule is seated before tightening
• Tighten fittings per manufacturer guidance; avoid over-tightening which can damage tubing
• After installation, turn water back on and check carefully for leaks

This elbow is a threaded pipe fitting that redirects and secures a fluid line connection where space or alignment requires a 90° turn. It provides a compact, threaded junction to connect compatible appliance tubing or hose to a valve or port. What it does:

• Connects two threaded line ends at a 90° angle for tight routing in confined spaces
• Provides a sealed, threaded junction between a 1/2 in. NPT inlet and a 9/16-24 threaded outlet
• Helps stop leaks and maintains proper line alignment when the original elbow is worn or damaged
• Commonly used where a bent or cramped connection prevents a straight coupling

• One elbow fitting (1/2 in. NPT x 9/16-24)

• Turn off and depressurize the water supply (or system) before removing or installing fittings
• Start threads by hand to avoid cross-threading; tighten with appropriate wrench until snug
• Use plumber's tape or thread sealant only if specified by the appliance manufacturer

This replacement wire clip secures refrigerator wiring to the cabinet side to keep harnesses organized and protected from abrasion. It helps prevent loose or pinched wires that can cause noise or intermittent electrical issues. What it does:

• Holds wiring harnesses against the refrigerator bodyside to prevent movement and wear
• Reduces rattling or vibration caused by loose wires
• Helps prevent chafing or pinching that can lead to intermittent connections or shorts
• Keeps wires routed away from moving parts and sharp edges

• One wire clip

• Disconnect power to the appliance before servicing to avoid shock
• Access may require removing an interior panel or trim; keep fasteners organized
• Clip typically snaps into a matching slot or fastener point; align wiring and press clip into place

This manifold panel is the replacement cover that mounts over the appliance manifold to protect internal tubing and provide the finished surface for controls. Restores proper fit and appearance after damage or wear. What it does:

• Covers and protects the manifold and associated tubing from debris and accidental contact
• Provides the finished mounting surface for control components and trim
• Helps maintain correct alignment of control openings and knobs
• Commonly replaced when the panel is dented, cracked, missing, or has broken mounting tabs

• Disconnect power (and gas supply on gas models) before starting any repair
• Use care handling sharp edges; wear gloves to avoid cuts
• Removal typically requires lifting or removing the cooktop/control assembly
• Secure all mounting tabs and fasteners; do not force mismatched parts

This adhesive identification label replaces a torn, faded or missing appliance sticker so model, serial or safety information is legible again. It helps you confirm appliance details for service, parts or safety checks. What it does:

• Restores readable model/serial and specification information that is printed on the original sticker
• Replaces damaged or faded identification and safety labels
• Makes it easier to verify the correct part or service information before repair
• Helps meet safety and inspection needs by restoring visible manufacturer info

• One adhesive identification label

• Clean and dry the mounting area before applying to ensure good adhesion
• Peel backing and press label firmly; hold for several seconds to set
• Avoid placing on textured or insulated foam surfaces where adhesion may be poor