Denise May 15, 2019 for Model Number SHX68T55UC/07 When I pour rinse aid into the dispenser it runs right out. What is the likely culprit? Do I need to replace the entire dispenser or just the seal?
1 Answer Denise, We're pretty sure replacing the 12008380 Dispenser assembly would be in the best interest and the easier repair to make. The constant rinse aid could most likely be due to a damaged solenoid or linkage to the dispenser plunger. Those parts are not available as individual parts. The dispenser assembly is in stock and available at this time. Thanks, Read More...
Amy May 03, 2019 for Model Number SHE3AR75UC/22 I have a 2 year old dishwasher. The rinse aid runs right out when I try to put it in. I had it replaced, and the new one does the exact same thing. What now?
1 Answer Amy, You will need to remove the outer door panel and inspect the dispenser assembly 12008380 / 12008380 for a damaged solenoid or actuator linkage to the rinse dispenser. If there is a problem in the dispenser linkage, it would continue to allow the rinse agent to dispense. If all checks OK, you'll need to check for constant voltage to the dispenser from the control board, which would also allow the rinse agent to dispense constantly. Read More...
K.J. March 29, 2019 for Model Number she43f12uc/64 Our rinse aid door will not stay closed. How do we know if it is the door or the part that the door attaches to?
1 Answer Hello K.J., This is normally caused by the latch and not the door. Due to the complexity of the dispenser assembly and the changes that have been made to it by the manufacturer, we would recommend replacing the complete assembly 00490467. Read More...
Cindy March 22, 2019 for Model Number SHX53T55UC/01 I use Finish rinse aid and have hard water with a water softener. The problem that I am having is the rinse aid (dishwaher) sticks to my small plates that are directly under the rinse aid dispenser. I have to use goo gone to remove the rinse aid that is like a residue after your remove a sticker that is left on the glass. I have tried running my dishwasher in two cleaning cycles using white vinegar. Just wondering if you might have anymore suggestions? Thank you
1 Answer Cindy, you may want to adjust how much rinse aid is being dispensed during the cycle. This can be done through the following: The amount of rinse aid dispensed can be set from "r:00" to "r:06".1 Press the [On/Off] button. 2 Hold down the "Auto" button and press [Start] until the display indicates "d:00". Release both buttons. 3 Press the "Auto" button until the display shows "r:05". 4 Press the "Rinse" button to select the desired setting. "r:00" = dispenser is OFF "r:01" = lowest setting "r:02" = low setting "r:03" = medium setting "r:04" = medium/high setting "r:05" = high setting "r:06" = highest setting. 5 Press [Start] to save the setting. Read More...
John March 17, 2019 for Model Number shp65t55uc/02 when rinse aid is filled the top rinse aid light remains on
1 Answer John, Measure voltage between outer most dispenser terminals. If ˜ 13VDC, replace dispenser. If not, replace the operating module. Read More...
Cia February 04, 2019 for Model Number SHE43R55UC/64 In the rinse aid dispenser - what is the dial with the arrow and numbers 1-6> Is it (the arrow) or supposed to move automatically or indicate the number of washes? the arrow never moves unless I manually move it. Thanks
1 Answer Cia, the indicator is designed to regulate the amount of rinse aide distributed during the rinse cycle. The lower the number, the smaller amount it dispenses. You will need to manually set it to the amount you want it to dispense, it does not move on it's on. Read More...
Mark January 17, 2019 for Model Number SHPM98W75N When we add even a very small amount of rinse aid to the dispenser, some of it immediately starts running out of the bottom of the dispenser. The washer seems to use up rinse aid rather quickly as well. How can we fix this?
1 Answer Mark, If the rinse aid is running out of the rinse aid door then the door would need replaced and is part number 00611575 and if it is not coming from the door then the dispenser 12008380 would need to be replaced. Read More...
Doug Johnson January 08, 2019 for Model Number SHV6803 UC/12 (FD 8105 -) I preserved a new detergent dispenser and when installed it will not lock into place. It leaks when I run the dishwasher. It appears the locking tabs are too long. How can I get it to seat properly?
1 Answer Doug, the dispenser can be difficult to install. You may need someone to help you push the dispenser in so that all the tabs click into place. Read More...
Ray January 05, 2019 for Model Number SHP65TL5UC/01 May use pn AP2802335 on Bosch dish washer SHP65TL5UC/01?
Pierre December 30, 2018 for Model Number 500 series Where is this indicator light for rinse aid? How do we know when the rinse aid tank is empty for sure? When the reservoir is full how many washes can I expect before it empties? How many drops of Rinse Aid is dispensed and when power wash?
1 Answer Pierre, A proper model number of the dishwasher would be needed for a better and more precise explanation. Basically, For dishwashers with a rinse agent sensor, the indicator light is usually labeled and located on the control panel. For machines with the "standard" rinse aid dispenser, there is a clear "eye" in the rinse agent door and dispenser, if the "eye" is clear, the dispenser is empty, if the "eye" has the same color as the rinse agent being used, the rinse dispenser has enough rinse agent, the color will dissipate as the rinse agent is dispensed. The rinse agent in a standard type dispenser usually dispenses 1/8 to 1/4 teaspoon of rinse agent, one time per wash cycle(the final rinse,usually). If the rinse dispenser is "adjustable" you can reduce the amount of rinse agent to a couple of drops to 1/2 or more teaspoons per load. These are "general" or "basic" information and tips, with a proper model number we can be more precise. Thanks, Read More...