Corinne September 17, 2020 for Model Number Bosch 800 series washer wfmc8400uc/09 Water is not coming into drum after I push the start button.
1 Answer Corinne, it would be recommended that the cold water valve 00422244 and hot water valve 00422245 are tested for 120VAC depending on what temperature selection is made. During the start of a cycle, the cold water valve should receive 120VAC if a warm or cold temperature is selected and the hot valve would receive 120VAC if hot or warm are selected. If there is 120VAC and the water supply going to the valve is verified, then the valve would need to be replaced. If there is not 120VAC, and the door locked properly, there may be a failure with the main control 00665847 or the wire going to the valve. It would be recommended that the wires are inspected for any broken or loose sections and connections. Read More...
1 Answer Geraldine, We will need to have the model number of your washer to be able to assist properly with your question. Please verify the model and resubmit your question. Read More...
Pete December 10, 2019 for Model Number wfmc3301uc/06 only hot water enters the machine regardless of setting,cold water supply is hooked up and has plenty of water and pressure
1 Answer Pete, If you have a rinse only setting, put the unit on that and start the cycle. Remove the top and check for voltage at the cold water valve. If no voltage is measured then replace the control. If you have voltage replace the valve. Read More...
Julius October 08, 2019 for Model Number Bosch Nexxt WFMC32000 UC/01 Hello, My front-loading Bosch Washer runs a few minutes on cold water setting, then shuts down. If setting is on hot water, washer runs perfectly well. Neither will it run on hot/cold setting. What seems to be the problem? Can it be solved by a do-it-yourself person? What part number/s need to be ordered? Approximately how much? Thank you. Julius (08Oct19)
1 Answer Julius, the water flow will need to be inspected for a slow fill time with the cold water. If the cold water does not fill appropriately it can cause the unit to shut down as a safety measure. If the water flow is low, and taking longer to fill, then the water hoses will need to be inspected. If the hoses check good, then the wiring harness will need to be inspected for a loose connection. If there is not a loose connection, then the most likely issue would be with the water valve 00422244. Read More...
Terry February 22, 2019 for Model Number wfmcc2201uc/06 Water will not stop running when in normal cycle. It fills the front load and flood the floor. Water runs even when power is turned off. You have to turn the cold water valve off to stop water from running into washer.
1 Answer Hello Terry, This will be corrected by replacing the water valve 00422244. This is the cold water valve, (most common to fail). If the water filling is hot, the valve that has failed is 00422245. Read More...
Katie October 21, 2018 for Model Number WFMC8440UC Hello - thank you for your website! I ordered part number AP3758492 in the hopes that it will cure my problem. When I am not using my Bosche washing machine for a few days, I notice there is water accumulating in the drum. The longer it is unused, the more water there is. Is the defective water inlet valve the most likely cause of water leaking into the drum? And is this the correct replacement part? The washer is 9 years old. Never had water leak under the machine.
2 Answers Katie, You are correct, this happens when the water valve doesn't seal correctly. You have two separate water valves for your hot and cold sides. I would suggest replacing as a pair. Hot side is 00422245 and cold side is 00422244. Read More...
Katie October 21, 2018 for Model Number WFMC8440UC Hello - thank you for your website! I ordered part number AP3758492 in the hopes that it will cure my problem. When I am not using my Bosche washing machine for a few days, I notice there is water accumulating in the drum. The longer it is unused, the more water there is. Is the defective water inlet valve the most likely cause of water leaking into the drum? And is this the correct replacement part? The washer is 9 years old. Never had water leak under the machine.
Brian October 18, 2018 for Model Number Bosch Nexxt 300 Wash machine WFMC220UC Water is not filling the fabric softener dispenser tray. I pulled tray and cleaned both the fabric softener and bleach siphons and both will drain. Water will fill up the bleach side and drains as it should when the cycle calls for bleach. What could be the problem for water not filling the fabric softener side? Do i need to replace the inlet valve? Thanks Brian
1 Answer Brian, The water inlet valve 00422244 would be the most likely issue for this problem. Read More...
Cytna June 07, 2018 for Model Number WFMC8401UC/10 My machine is not sending the water through the fabric softener nor the bleach tray. All water is coming through the main water chute. Not sure which part will fix this. Thanks
1 Answer Hello Cytna, You could have a stopped up dispenser 00640612 or a bad water valve 00422244. I'm sorry but this part 00640612 has been discontinued by the manufacturer and no satisfactory substitutions have been provided. Thank you for your patience and understanding in this matter. Read More...
David December 31, 2017 for Model Number bosch wfmc2201uc/03 Serial # 856100084484010535. Tub fills with water when off. What is the correct water inlet valve?
1 Answer David, It would depend on if the water is coming in cold or hot. If it is hot water running in then you would need part number 00422245 and if it is cold water then this will be part number 00422244. Read More...