Dwayne August 08, 2020 for Model Number EW30EF65GSK I had a F 14 error and I replaced the control board and I am still getting the same F 14 error and the oven doesn't heat. Any ideas?
1 Answer Hello Dwayne, the fault code refers to the oven control board not detecting the control panel correctly. Ther control panel has the connector ribbons as part of its assembly. Check the ribbon ends are securely connected , check the ribbons for any breaks, the control panel is part 316538416. Read More...
Florante T. June 27, 2019 for Model Number EW30IS65JSD Error "E15" on my Electrolux Induction Range. It won't stop even if I turned the breaker off and on. What do you think is the part the I will replace and if you have that part? Thanks
1 Answer Hello Florante, F15 on the model provided indicates the following: F15 Controller self check failed or terminal cutoff open. 1) if the oven controller displays an F15 error code and the ESEC controller displays an E15 error code at the same time, this is a strong indication that the safety thermostat (thermal cutoff) inside the front console opened. The primary reason for a safety thermostat to open is a deficiency of the cooling fan. With an ohmmeter, verify if the thermostat tripped. Reset the thermostat is needed and verify the operation of the cooling fan. Note: the safety thermostat, when open, cuts AC power to the oven relay board (connector J4, pin 1 and 3) and the ESEC relay board (connector J1, pin and 3). 2) An F15 error code on the oven controller may indicate the oven controller is not receiving a synchronization signal from the relay board. One easy way to determine this is to power off the unit, power it on and start a Timer for 1 minute before the F15 error code appears. If the timer counts-down normally then the synchronization signal is okay. If the timer stays at 1:00 and does not count down, then the synchronization signal is missing. If the synchronization signal is missing, check first if the oven relay board is receiving 120VAC correctly (J4 pin 1 and 3). Then check the wiring between connector J2 on the relay board and connector P16 on the oven controller. If AC power and wiring look good and the problem is still there, replace the relay board. If the problem persists, replace the oven controller. 3) The F15 error code may be caused by an oven controller failure. If the safety thermostat and synchronization signal have been verified and tested good, replace the oven controller. Read More...
Ken February 28, 2018 for Model Number EW30EW65GS7 Top oven lights will not go off. Bottom lights will not come on at all. Rest of the unit works ok. Relay Board, Triac boards?
1 Answer Hello Ken, If there are no wiring issues, the issue is most likely the triac board 316519200. Read More...
Michael May 20, 2014 for Model Number EW27EW65GS3 On diagram they list 97A for this part 316519200 we replaced because lights on lower oven wouldn't turn off and convection fan wouldn't come on saw where this may be issue. Where is this located at? Taken some of the parts off the oven still can't find, please help locate. Please be specific left , right etc if you can. Thank you.
1 Answer Michael, To replace the relay board, Disconnect the wall oven from electrical supply. Remove the oven from the cabinet. Remove the back panel. The relay should be located on the right side when looking at it from the rear of the unit. Read More...
Cary April 01, 2014 I have an electrolux induction stove I am unable to find the model and serial no. The panels were changed I am getting e 75 and e35 error I need a power relay board. Do you have it in stock?
1 Answer Hello Cary. Sorry, We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...