Sudhir May 18, 2017 for Model Number electrolux eidw61055gs1 dish washer not drying the dishes. I checked the heater with ohm meter and its working fine, what else could be wrong with dishwasher. I ran it with high temp and increased my water heater temp which did not help either.
1 Answer Hello sudhir. Check the high limit thermostat. If good, then you will need to replace the control board on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Mark H. March 29, 2016 for Model Number EIDW6105GS1 This unit will fill and start to wash and I can hear a low level thumping sound coming from underneath. Suddenly it stops and pumps out. All control leds are flashing. No problem led from the panel below. I have replaced the control panel and the door switch in the recent past; however this irregular thumping sound as it attempts to wash is somewhat new. I do a reset and it will start again but no sooner than it starts wash it pumps down and stays in trouble mode. Seems to fill and pump out all of the way.
1 Answer Mark, You will want to open the circulation pump and make sure that there is nothing caught in the pump assembly which could trigger this issue. Read More...
Alfred H October 12, 2015 for Model Number EIDW6105GH1A I have a EIDW6105GS1A dishwasher, All led's on the door were flashing. I removed the bottom panel and found the drain valve led lit. Can this be repaired or should it be replaced.
1 Answer Alfred, You will want to check to make sure that the unit is not in control lock. You can open the door and press the air dry for 3 seconds. If this does not correct then check the door switches on the unit. If these check ok then the drain valve would most likely be the cause. Read More...
Ben May 06, 2015 for Model Number EDW7505HPS1B We have an Electrolux dishwasher that is approx. 2.5 years old. We started getting error code 11 intermittently. Around the same time the dishwasher started to overfill and leak out the door. We had a repair service in who checked the drain for debris and checked to make sure the drain hose was high enough. Unit worked for a cycle or two and then problems returned. Control board was replaced, that did not fix it either. We gave up on that repair service company. I used a meter to check the float valve and water inlet valve and both test fine. Before I replace more parts (i'm almost at the price of a new dishwasher now) I'm hoping somebody with some experience can provide some better guidance. I'm basically guessing at this point. Thanks in advance
1 Answer Ben, The Er 11 error would be that the unit has timed out before finding the state for the drain valve. You will want to check the drain pump to make sure that there is power going to the drain when it is time to drain. If not then the drain pump would need to be replaced. Read More...
Doug January 14, 2015 for Model Number electrolux dishwasher EWDW6505G50 This dishwasher is making a loud annoying snoring noise when washing. I have changed the main motor pump assembly and the drain motor pump assembly. Still no luck. Any ideas?? Thanks Doug
1 Answer Hello Doug. You need to check and see if the unit is filling to the proper level inside. If not, it may be drawing air and need the water valve replaced. Also, try cleaning out the filters inside the unit as well. Read More...
Rick M May 08, 2013 for Model Number EWDW 6505 I was getting error 11 and I replaced the drain valve. All hoses are secure and tight. However I'm still getting error 11. Any ideas why?.
1 Answer Rick, If you have check the wiring between the main control board and drain valve and you have already replaced drain valve then you will need to replace the main control board. Read More...
Carmen November 09, 2012 for Model Number EDW7505HPSO electrolux icon disahwasher I get error code ER 11 drain valve -time out before finding a state for the drain valve. Not sure what that means. Do I have to replace the drain valve?
1 Answer Hi. Remove the lower panel. The drain valve is a white body part # 154622001. Make sure the connections are clean and tight. Make sure the internal impeller is not clogged or spinning loose on the shaft. Replace if so. Make sure the drain hose is not clogged. Make sure the drain hose at the sink is not clogged as well. Follow the installation instructions (w/ User guide) to verify the hose is properly installed. Thank You. Read More...
John August 23, 2012 for Model Number EIDW6305GS1 If the machine is draining partially,besides the pump,does this part have something to do with it?
1 Answer Hello John. Yes, if the drain valve 154622001 is clogged or bad it can cause the issue you are having. Read More...