Mike March 31, 2024 for Model Number GTD33GASK0WW Will this replacement kit work for my specific dryer?
Kristin November 19, 2023 for Model Number GFD45GSSM0WW I’m having much difficulty finding the dryer bearing kit for my GE dryer model GFD45GSSM0WW. Will kit WE49X20697 be compatible with this dryer?
1 Answer Kristin, For your model machine, the drum Support Shaft and Bearing are part# WE3M33 Read More...
Ben G August 08, 2023 for Model Number DHDSR46GG7WW Hi I would appreciate your help with 3 questions... Will Dryer Bearing Kit WE49X20697 / AP5806906 Part Number: AP5806906 work for GE dryer model DHDSR46GG7WW? Is there a similar 'kit' that includes felt seal and housing seal along with the Lint Chute Assembly or does AP6032647 include the seals? I am planning to replace both the front drum bearing and the lint chute assembly since they have become brittle and cracked over time, is there anything I need to check regarding the drum function? I am not having any problems drying clothes. Thank you
1 Answer Ben, Both WE49X20697 and WE14X25080 will work for your unit. The lint chute assembly will be the lower section with the duct and if you are needing the upper bearings then you would need part number WE49X20697. The lint chute will have seals but so will the upper bearing assembly. Read More...
Dshlamowitz February 21, 2022 for Model Number dshlamowitz@abouttimesnow.com my GE dryer model number is DPXR473EW0AA the front bearing and slides are gone will the repair kit WE49X20697 replace the old part correctly
1 Answer Dshlamowitz, This dryer bearing kit [AP49X20697] would correct the issue you are having. Read More...
Mark February 13, 2022 for Model Number DPSQ475GT4WW I'm installing the following parts into GE Dryer model: DPSQ475GT4WW. (1) WE49X20697 (Dryer Bearing Kit) (2) WE14X25080 (Lint Chute Assembly) Since the kit comes w/the top bearing WE3M26 and the belt, (WE12M29), is there a suggested order of installation between these chute assembly, the top bearing and the belt? Or does it not really matter? Thanks.
1 Answer Mark, If the top bearings are not installed then the green ones go in the 2 slots on top and the white/gray ones will go on the ones that are lower. Read More...
Brian January 09, 2022 for Model Number DPSB513GB0WW Hi,Hope this email finds you well. I have a GE gas dryer Model #DPSB513GB0WW that will not start. The control panel lights up and when I push start i can here a relay click but does not run. I checked out the usual suspects such as the door switch and the broken belt interlock switch, all test fine. I also conducted the field test on the board and it cycles through with all codes as they should be, however the motor does not start. Pulled the motor and bench tested it and it runs fine.Is there any other device that would prevent it from starting up? This one has me puzzled. Looking forward to your advice. Thank you, Brian
1 Answer Brian, based on the information provided, the main control WE4M296 motor relay has failed and the control would need to be replaced. Read More...
Bill September 17, 2021 for Model Number DBSR453EB2WW What part supports the bottom of the rotating drum below the top bearing kit? Is it part the of the Dryer Hot air exhaust duct?
1 Answer Bill, The dryer rides on the top bearing and that is it in the front. The rear has a middle bearing for support. Read More...
Ivan August 23, 2021 for Model Number DJXR433EG7WW What bearing kit or will this kit fit Model #: DJXR433EG7WW
1 Answer Ivan, The bearing kits for your model machine: WE25M40 rear bearing kit and WE49X20697 front bearing kit Read More...
Tim May 17, 2021 for Model Number DPSR483GA2WW Is WE49X20697 compatible with my dryer DPSR483GA2WW? The individual part is listed as compatible but the kit is listed as incompatible.
1 Answer Tim, The kits are not listed as compatible due to the fact they are not part of the original parts list, the kits were added after the parts list was published. Read More...