J. February 23, 2018 for Model Number GE GHDA480N10BB Bottom arm spins very slow and top 2 only run water no spinning. Dish detergent tabs don't always dissolve if they don't land in the right spot and dishes are not clean. Cleaned out all of the inside parts and found no clogs. We replaced the water inlet valve 3 years ago due to overflowing.
1 Answer Hello J., If there are no clogged screens and nothing is wrong with the pump impeller, you will need to check the water fill level. If the unit is not filling with enough water it will give the same symptom as a clogged screen so the water valve WD15X10003 would need to be replaced. Read More...
Miked May 23, 2017 for Model Number GSD4320Y72BB When running water in sink with garbage disposal, where dishwasher drain is hooked too, dishwasher leaks water out of bottom. Is this a hose or a drain assembly issue? Thank you
1 Answer Mike, This issue would most likely be either the drain hose leaking or the disposal that may be damaged. It would be more likely an issue of the hose. Read More...
John February 18, 2016 for Model Number PDW7380N20SS My dishwasher no longer drains. It will run through a cycle but at the end there is standing water in the bottom of the unit. I have taken it apart from the inside to clean out all of the filters and the sump basket, etc., but am still having the same problem. Also, when I run the unit on a quick rinse cycle, a few minutes in (during what I expect is the drain cycle) there is a low humming noise which I am thinking might be the drain pump trying to work. Does this sound like it might be the problem? I am wondering if I just need to replace the drain pump unit. Thank you.
1 Answer Hello John. Check and see if there is power to the pump and the hoses are not clogged. If so, then you will need to replace the drain pump on the unit. Read More...
1 Answer Elizabeth, To replace the drain pump on your unit, you will need to remove the kickplate of the unit. It may be possible to remove the drain pump without taking the unit out from installation but would be best to pull the dishwasher out and lay on its back and remove the pump and install the new one. Read More...
Jacob P March 05, 2014 for Model Number glc4100n14bb My dishwasher wouldn't drain. so I emptied it and flipped it over and took apart the drain basket and motor and cleaned it out. hoping to fix the problem. now with it all back together when I plug it in the normal wash and heated dry lights flash and the motor hums and that is all it will do. Any suggestions?
1 Answer Hello Jacob. It sounds like you have something binding in the motor assembly. You will need to take back apart and check everything. Read More...
Greg December 01, 2013 for Model Number GE Dishwasher GLC4100N10WW Our unit worked very well until here lately. It will wash & run well but when it kicks on to pump in any cycle, it pumps out very little water. Does this sound like I need to replace the drain pump assy? Thanks for your help.
1 Answer Greg, it is possible the pump itself is bad, sometimes the impeller will slip on the shaft. Before you replace it you probably should check for any obstructions in the hoses going to and from the pump. Also make sure there isn't anything in the pump itself. These small electric pumps are notorius for clogging with lint or sometimes the backing off of certain rugs, etc. Read More...
Ashley October 27, 2013 for Model Number GLD4500N10BB Our dishwasher started having water settle on the bottom of it. Today when we ran it, all the water came running out. We have taken it apart and checked the lines and they are all clear. I just need to make sure it is a new pump that we need to order?
1 Answer Hello Ashley. It sounds like the water valve WD15X10003 has a slow leak and will need to be replaced on the unit. Read More...
Asquared September 18, 2013 for Model Number GE profile dishwasher model PDW7880N00SS I need to replace the drain pump assembly. Do you the right part for this model. What is the cost. I will doing the replacement myself.
Jon May 13, 2013 for Model Number Gld4500n10bb Hi my dishwasher powers ups but when I hit start nothing happens and the water will not drain or pump in.
1 Answer Hello Jon. Based on the information you provided, it sounds like the main control board WD21X10247 is bad and will need to be replaced on the unit. Read More...
Cptgro February 06, 2013 for Model Number pdw7300j15cc How can I tell if my drain pump is bad before I pull it out? My machine fills but doesn't drain any water. I checked the sump to see if it was clogged and it doesn,t seem to be. When it runs through the drain cylcle it feels like the pump is running when I put my hand on it. Any idea's.
1 Answer Hello cptgro. There is no way, you need to pull out the unit and check and see if the pump is pumping water. If not, you will need to order and replace the drain pump WD26X10025 on the unit. Read More...