Customer Questions and Answers for Temperature Switch (Dryer) by Ge

Best Seller

Manufacturer Part

Temperature Switch (Dryer)

4.89 (64)

By: Ge

Part Number: OEM13038249

Manufacturer Part Number: WE4M406

This temperature switch mounts in the dryer control panel and lets you select the desired heat level. Replacing a failed switch restores accurate temperature selection so the dryer responds properly to the setting you choose.

Selects the heat level for drying cycles
Routes power through the appropriate heating circuit based on your selection
Failure symptoms include no change in temperature when turning the knob, being stuck on one heat level, intermittent heat, or a loose/stripped switch shaft
An internal short or open may contribute to a no-heat condition while the drum still runs

Includes: 1 temperature selector switch Install notes:

Disconnect power before servicing; for gas dryers, also shut off the gas supply
Remove the control knob and open the control console/back cover to access the switch
Note wire positions; transfer connectors to the new switch one at a time to avoid miswiring
Mount the new switch securely, reassemble the console, reinstall the knob, and test heat selection

$90.79

Compare At:: $127.84
You Save:: $37.05

IN STOCK

Ships Today Guaranteed

Add to Cart

Questions & Answers

For Ge Temperature Switch (Dryer) (Part Number: OEM13038249)

Don April 05, 2024 for Model Number DPSR610EG2WT

No matter what temp setting, dryer only heats high temp

1 Answer

Don, with the power cord unplugged, the heating element WE11M23 would need to be tested for continuity to the tub and the element element housing. If there is continuity, the element would need to be replaced. If there is not continuity, the temperature selector WE4M406 would need to be tested for continuity from terminal 7 to terminal 8, and terminal 7 to terminal 6 when it is set to low temp. If there is not continuity, the temperature selector has failed.

Steve January 26, 2023 for Model Number DWSR405GB1WW

dryer stopped before end of cycle. Turned the rotary start switch and started again but only while I hold the switch. Replaced the switch from local supplier still works the same. If I hold the switch in the start position the dryer will run and fire and dry till I let go. Is there a circuit breaker in the in the line somewhere?

1 Answer

Steve, If the dryer shuts off when you release the start button then this will be a motor issue.

Glenn September 26, 2018 for Model Number PTDN600EM0WT

DRYER WILL NOT START THE START BUTTOM FEELS SOFT OTHER THAT THERE IS NOTHING

1 Answer

Glenn, That button can be tested for continuity. Other than that you have to make sure door switch is not broke or failed, the voltage needs to be 240 vac at the terminal block. If all these test good you will need to check the all thermostats and fuses on the rear heater assembly for continuity. You can also open the door and hold the door switch press start and turn the drum by hand if it starts your motor needs replaced.

Charlie June 10, 2018 for Model Number GTDP490ED5WS

Dryer failed while it was working on a load. The dryer stopped and load was not really dry as usual. Then push the Start button, the blower is working, however it won't start any more. What could be the reason?

1 Answer

Charlie, If the dryer will not run then check for a broken belt, a faulty door switch or a bad thermal fuse on the unit.

Christinec0 August 18, 2017

GE Dryer Model GTDP490ED5WS Buzzer was sounding even when new load of wet clothes put in, Timed dry setting. After about 5 signals, it shut off. Will not come back on. I've replaced PC clothes dry board. Tested door, and start buttons. Help please. Thankyou.

1 Answer

Hello ChristineCO. You will need to order WE4M527 for the timer needed for the unit. This should resolve the buzzer issue.

Bill June 07, 2017 for Model Number GTDP490ED2WS

Dryer will not turn on. Tested fuse and it is ok. I did notice that the vent was very restricted. I was able to rotate drum and it seemed ok.

1 Answer

Bill, You will need to check the fuse on the blower housing to make sure that it is good. If this is good then test the door switch to make sure that it is good. These would be the most likely causes for the unit not running.

Francis July 30, 2016 for Model Number GTPD490GDOWS

Pushing button to start machine results in unit starting but upon releasing button machine stops working..Will only operate while holding finger on start button What part needs replaced to fix this??