Kevin Cotter February 02, 2019 for Model Number LFC23760SW I need some step by step instructions on how to replace the following part: Cam, shaft Part Number: AP4437126
1 Answer Kevin, On the inside of the door there will be a cover that goes over the door gasket that you will need to remove. Once this cover is removed you will have access to the holder for the gasket which the cam will screw into the top of. If the cam broken off then it may be necessary to replace the holder as well as the cam. Read More...
Tammy B. May 26, 2018 for Model Number LRFC22750SW Both doors cams have cracked off. I see the right door has the broken piece of the cam and the shaft I see the left door doesn't have either. What do I need to order? Thank you
1 Answer Hello Tammy, You will need to order ADX73410707 for the right fresh food door and ADX73410701 for the left fresh food door to get the door cams since they have not been made available b the manufacturer individually. Read More...
Vp July 24, 2016 for Model Number LFC23760AT The door closers on both doors have broken off. Can I just purchase a left and right door closer or do I need additional parts because they have snapped off?
1 Answer VP, Along with the cams you would need to get the gasket retainers for both the left 4930JJ2028D and right 4930JJ2028A. The reason these would be needed is due to the holder has most likely broken where the screw goes into the holder where the cam is located. Read More...
Maria January 27, 2015 for Model Number LG Model # LFC22760 My right side door lock broke off. I wanted to confirm that the part I need is LG 4430JJ2005A. Is this difficult to replace? it snapped off.
1 Answer Maria, This cam shaft 4430JJ2005A is screwed to the top of the flange that holds the side of the door gasket. You may not be able to just replace this. There is a trim on the inner corner of the door in which you would grab from the bottom and work your way up to get this trim cover off. Once off there is a plastic piece that holds the door gasket, this is most likely what will be needed to be replaced on your unit. Read More...
Jan January 26, 2015 for Model Number LG FRIDGE LFX25975ST I NEED TO LIMIT THE SWING ON ONE DOOR TO 90 DEGREES IS THIS POSSIBLE?
1 Answer Jan, Unfortunately there is no way to limit the swing of the door to 90 degrees. Read More...
Jeff August 20, 2013 for Model Number Kenmore Refrigerator 79571302011 How to install the Cam Shaft, Part # 4430JJ2005A? Mine broke off on the right-side door. Also, is it connected to another part in the door that I need to order? Thank you.
1 Answer Hello Jeff. The cam shaft part # 4430JJ2005A slides into the center divider holder. To remove the cover you will start from the bottom and pop each clip out as you move up the cover. You will need to replace the lower one also part # is 4430JJ2005B. Unless the top and bottom corners of the gasket is... more not sealing, then you normally do not need to replace a gasket. The inner magnet inside the gaskets onlt go close to the actual corners anyway. As londg as they are close. Also you can use a hair dryer to heat a putty knife to lightly "persuade' the gasket back into place. Read More...
Steven June 02, 2013 for Model Number Kenmore refridg 795.78402.801 I have anew gasket holder for the right door. I have inserted the screw, but would like to remove the plastic protection panel. It appears to be held on with clips, but I obviously do not want to break them inthe removal. I have inserted the new cam shaft with screw into the holder. How may I proceed to remove that panel? Thank you
1 Answer Steven, To remove the cover you will start from the bottom and pop each clip out as you move up the cover. Read More...
Katie C. December 27, 2011 for Model Number Lfc20760sb How do you replace this part? It is just loose in the top of the door but I can't tell where it is broken. Door still has a tight seal and gasket appears to be in good shape still. Left side is fully intact.
1 Answer Hi Katie. The cam shaft part # AP4437126 slides into the center divider holder. You will need to replace the lower one also part # is 4430JJ2005B. Unless the top and bottom corners of the gasket is not sealing, then you normally do not need to replace a gasket. The inner magnet inside the gaskets onlt go close to the actual corners anyway. As londg as they are close. Also you can use a hair dryer to heat a putty knife to lightly "persuade' the gasket back into place. Thank you. Read More...
Doug K September 30, 2011 for Model Number LG FRIDGE LFC20760ST Two questions: 1) Cam shaft #AP4437126 on the right door connects by a screw into a holder gasket, but the diagram is unclear as to the part # -- is it holder gasket AP4633397 or holder gasket AP4440023? 2) The holder gasket cracked where the screw from the cam shaft attaches --how do you remove and replace the holder gasket?
1 Answer Hello Doug. 4930JJ2028A is the holder for the right door. It unsnaps from the door with clips. Hope this helps. Read More...
Kenneth E. September 22, 2011 for Model Number LFD22860ST I wish to replace broken AP4437126. Do I need to replace door seal? Can you tell me how to replace this part? Ken
1 Answer Hi Kenneth. The cam shaft part # 4430JJ2005A slides into the center divider holder. You will need to replace the lower one also part # is 4430JJ2005B. unless the top and bottom corners of the gasket is not sealing, then you normally do not need to replace a gasket. The inner magnet inside the gaskets onlt go close to the actual corners anyway. As londg as they are close. Also you can use a hair dryer to hest a putty knife to lightly "persuade' the gasket back into place. Thank you. Read More...