1 Answer Hello Gerhard, thank you for contacting Appliance Parts Pros. Ignitor [MEE61841401] is used for the convection/bake and the broil, 2 separate parts but the same part # for each. Read More...
Katie January 16, 2025 for Model Number LSG4513ST/00 OUR STOVE STARTED SMELLING LIKE GAS WHEN STARTING AND SLOW START UP. THE FAN IN THE BACK WOULD STICK AS WELL. OUR BURNERS WOULD SOMETIMES PRODUCE BLUE/ORANGE FLAME THEN BACK TO BLUE. WE ARE NOW GETTING AN F9 ERROR AND IT WILL NOT HEAT UP. OUR FRIDGE IS ALSO ON THE SAME CIRCUIT AND IS NOT COOLING. I AM WONDERING IF A FAULTY IGNITER COULD CREATE A SURGE AND THEN CAUSE THE COMPRESSOR OVERLOAD ON MY LG LMXXS30776S/03 TO FAIL. WE ALSO HAD 2 OUTLETS AS WELL AS OUR CGFI TRIP. COULD THIS ALL STEM FROM A FAULTY IGNITOR?
1 Answer Hello Katie, thank you for contacting Appliance Parts Pros. It is unlikely that an igniter would cause all of these issues. The fans for this unit are on separate circuits within the unit from the ignition/gas systems, The flame discoloration of the top burners may be due to impurities in the incoming gas or pressure issues. The F9 code is the unit's way of saying it is not seeing any temperature rise in the oven over a certain period of time. The initial slow ignition and subsequent lack of ignition in the oven may be due to an igniter [MEE61841401] or gas valve [MJX62571702] failure. It is also highly unlikely for the glow-bar igniter or the gas valve to be able to fail in such a way as to backfeed through the board and back into the source electrical circuit to trip a refrigerator's compressor overload and trip a GFCI. It is more likely, in my opinion and experience, that the oven ignition issues and the refrigerator's compressor not running may have been caused by the source electrical circuit. Most modern large appliances, including the range LSG4513ST and the refrigerator LMXS30776S, are designated by the manufacturer to be on dedicated(separate) circuits by themselves without any other loads. It is also not required or recommended by the manufacturer that this gas range be run on a GFCI circuit. Read More...
Walt July 27, 2024 for Model Number LRG3091ST I want to replace the gas oven igniter. We get an F11 message. Please confirm correct part number. Range works fine, oven Does not. Thank you.
1 Answer Walt, if this is occurring only in a bake cycle, the ignitor MEE61841401 would be the most likely cause of failure. Read More...
Ed K April 02, 2024 for Model Number LSG4513ST MY BROILER DOESNT WORK..WILL NOT LIGHT UP..FIRST THE LOW END BROILER WENT OUT THEN THE HIGH END WENT OUT..NOW NOTHING..THE OVEN WORKS BUT THE TEMPERATURE SOMETIMES MOVES UP OR DOWN..MY QUESTION IS IF I REPLACE THE THE OVEN IGNITOR WILL THAT HELP MY PROBLEM WITH THE BROILER..THANK YOU ED
1 Answer ED, Check the resistance of the igniter for 40-400 ohms at room temp. If you have that reading then the main board is not sending voltage to the igniter and would need to be replaced. Read More...
Joe November 25, 2023 for Model Number LRG3091ST/03 Looking for the correct oven igniter for this model, I don’t see the model number listed on the MEE61841401 igniter.
Mike B November 26, 2021 for Model Number LDG3036ST Getting a f19 error code, LG service said it is for lower oven ignitor. I cannot find one in Parts Breakdown. What is the corect part number?
1 Answer Mike B, Thanks for the question!!! The correct part for your model is MEE61841401. Read More...
Kenny February 12, 2021 for Model Number LDG3036ST The igniter on top oven how do you access the 5/16 mounting screws they are easily accessible on a single oven once you lift the burner shield. However on top oven can see them but no room for nut driver.
1 Answer Kenny, If you are unable to get a nut driver in to get the screw then you will want to access using a open end wrench. Read More...
Jean January 08, 2021 for Model Number LRG3081ST/00 Do you have a video of how to replace the ignitor on this range? Is mee61841401 the correct part to use on my lg range? Appreciate your help!
1 Answer Jean, There is not a video for this igniter but should not be difficult to change out. If you open the oven door and remove the racks and the oven bottom, this should give you access to the igniter to change it. Read More...
Roy December 07, 2020 for Model Number LRG3095ST Is there a video available for replacing the ignitor to solve F11 Error? I followed a video for a dishwasher pump repair which was excellent. This repair seems similarly challenging and following a video would be helpful.
1 Answer Hello Roy, unfortunately, we do no t have a repair video at this time for this part. Read More...
Mike December 07, 2020 for Model Number LRG3097S Is this correct igniter? Did not see as I am looking in the units tech sheet and symptoms are similar, but model no. doesnt match up exactly. Want to be sure before ordering. Thank yoj.
1 Answer Hello Mike, this is the correct ignitor MEE61841401 for the bake burner on your model. Read More...