John Jones August 20, 2023 for Model Number WT7500CW my washer drips water by the nozzel assembly when not being used could it be water inlet valve this is a LG top load machine
Rick Kilborn December 29, 2022 for Model Number WT7200CV/00 My washer is leaking at the overflow point where the water flows to the bleach holder to mix. It appears to be sending too much water or water too fast to the cup will this replacement fix it?
1 Answer Rick, The water valve for this unit would be part number 5221EA1008F and will most likely take care of the problem you are having. Double-check the dispenser to ensure that it is not damaged or clogged. Read More...
J D December 03, 2022 for Model Number LG WT1101CW Cold water keeps coming in at a low rate even when machine is off. Bought a water valve off Amazon. Installed it and when the water started coming in there was a lot of hammering noise coming from the water valve. Shut off machine and it continued until I cut off the water (hot and cold). Do you think the new valve was a cheapie and was not strong enough to close the valves, Hot and Cold? Reinstalled the old valve (same thing, cold water coming in) and I am thinking I should order an LG part to replace the old one! ???? Is there any possibility the voltage is not enough to completely close the valve?
1 Answer JD, The water valve voltage is to open the solenoid and not close it. Check to make sure that the water pressure to the unit is not too high but it sounds likely that you will need a new water valve. The valve you got from somewhere else may not have been OEM and it is recommended to use OEM parts. Read More...
Vinay June 23, 2022 for Model Number kenmore 79635123210 I replaced the inlet valve a few years back because of the water fill issue. Now I am experiencing an issue where I turn the machine ON and the water does not fill. The machine makes funny noise and then nothing. Not sure what to replace ; an inlet valve or water control switch. Any suggestion.
1 Answer Vinay, unfortunately, the model number provided does not show as a valid model. If the model could be verified and provided in a new question, this may allow for the most accurate information to be presented. Read More...
Michael February 20, 2022 for Model Number WT1101CW Water keeps dripping from the water dispenser will i need to purchase a new water inlet valve to fix the problem?
Michael February 20, 2022 for Model Number WT1102C Water keeps dripping from under the soap dispensor will i need to purchase a new water dispensor?
1 Answer Michael, unfortunately, the model provided appears to be a partial model. If the full model could be verified and provided in a new question, this will allow the most accurate information to be presented. Read More...
1 Answer Mark, This unit has a thermistor in it and you will want to test the thermistor. The thermistor is part number 6322FR2046G. Read More...
Brian November 08, 2021 for Model Number wt7300cw My LG top load washer will not fill up with water.It start fill then slows to a very small stream.then the washer will stop and give a code of IE.
1 Answer Brian, it would be recommended that the inlet valves are tested for 120VAC during the fill cycle. The yellow wire and blue wire solenoid would be tested for cold water, and the blue wire and red wire solenoid would be tested for hot water (both would be used for warm water and the hot water valve would be turned on only long enough to reach temperature). If the valves are receiving proper voltage but the water flow is low, the next step would be identifying if the hoses are clogged up. If the hoses are clear and are not pinched, then the water valve has failed and would need to be replaced. Read More...
Robert April 19, 2021 for Model Number WT7200CV/00 LG washer WT7 200CV..... when set water to HOT.....only cold water is dispensing all the time. I tried to change to WARM, and still cold water is coming out! Do I need to replace the water valve? PS.....there is hot water available in the incoming valve (I checked it myself). Help please and thanks.
1 Answer Robert, You will want to check to make sure that there is 120 vac to the water valve. If there is power then check to make sure that the screen is not clogged and if it is not then the valve would need to be replaced. If there is no power then the control board would be the issue. Read More...
Billy August 18, 2020 for Model Number WT4970CW My washer continues to fill with water even after being unplugged from the wall. It happens during the rinse cycle. I replaced the water level pressure switch but that didn't help.
1 Answer Billy, this would indicate a failure with the water inlet valve assembly AJU75152601. Read More...