Headley B October 11, 2014 for Model Number Sears Cold Spot# 106720420 I got this old Sears Cold Spot Freezer and I need to repaint the outside . Is there any format that I have to follow? eg "Do I have to prime it or just fine sand and paint?" How many cans of paint do I need to get? (Its a stand up freezer about 6" tall x 30' wide) any info will be appreciated thanks
1 Answer Headley, You would want to sand and prime the unit if you are trying to repaint because of rust. Unfortunately we do not have information on what the coverage area for the Appliance spray paint 285006 is. Read More...
Holly September 07, 2014 for Model Number coil electric stove I want to repaint an older electric stove it. It is almond now. But I've heard the stove top gets to hot and paint won't stick. Is that true?
1 Answer Hello Holly! Yes, that is correct. You'll need to use an appliance high heat paint. Even then with the top being so close to the heat it will more than likely chip overtime. Sorry. Read More...
Kelly August 24, 2014 for Model Number rbd245pdq15 I want to change my white double oven to black. The glass doors are no longer available. Will this paint work?
1 Answer Hello Kelly! It's not recommend to spray paint or paint the outer door glass on the oven door. The paint won't hold up and will chip off due to heat. Sorry about that! Read More...
Jackie May 30, 2014 for Model Number DU810DWGQ0 I have a white Whirlpool dishwasher that I would like to spray paint black. Will this appliance spray paint work and if so how many cans do you think I'll need?
1 Answer Hello Jackie, I would recommend two cans in case you have problems with overspray and re-shooting. Read More...
Willie November 17, 2013 for Model Number rbs245pdb12 I have a white built in range and I want to convert it to black. All items are in stock except the side trims, left & Right, bottom trim and the handle (they are no longer available) to make by white built in oven black. Can I paint the white I currently have with your black appliance paint item # AP3075396 and do you think it would turn out okay? Need advice.
1 Answer Hello Willie, There should be no problem with painting these parts as long as none of the parts are directly exposed to heat. Read More...
Eileen June 26, 2013 for Model Number GR2SHTXKB00 We are remodeling our kitchen but love our 12 yr old Whirlpool, black refrigerator and will keep it for awhile. As luck would have it, the contractor put a scratch right on the front of it while moving it. We tried to repair it with the brush-on Whirlpool touch up paint but I think we can do better if we lightly sand the area, tape it off and use the spray paint. Does this sound doable? The contractor mentioned replacing the "skin" on the door (at his expense) but this sounds like a big deal. Any thoughts on that? Thanks for your input.
1 Answer Eileen, If the door panel is a textured then it would be harder to sand down and spray paint and get the same texture. It would not be difficult to replace the door skin for the door. Read More...
Joe C. December 20, 2012 for Model Number kenmore coldspot 106-59429801 considering re painting black with white will it work. saw answer that said first coat vertical second horizontal then third coat more critical as it is finish coat--any suggestions to making this coat look better one direction spraying same as second same as first -other suggestions/
1 Answer Joe, Make sure you wash down the unit thoroughly, you may want to use a strong chemical cleaner, like TSP, especially around the handle areas. Make sure you use a medium grit sandpaper and "rough up" or dull the original finish, then wash it all down again. Use a "tack Wrag" and wipe down the unit just before you start to paint. It doesn't matter which direction you start at (Vertical or Horizontal) but you don't want to be too close to the cabinet, and you need to move relatively quick. You want to first coats to go on more like a "powder" coat" and wait 20 to 30 minutes to allow the paint to "flash" before you start the next coat. After a few days (3 to 5) then "hand wax and polish" the finish with car polish. Just take your time and be patient, color changes can be frustrating. Read More...
Rich October 03, 2012 for Model Number Ventline Range Hood PR-4 Is this black paint high gloss? How many cans to do a range hood 42" x 18"? Thanks.
1 Answer Rich, the spray paint 285006 is listed as a superior black. We do not have the specs to verify if this paint is a flat black or glossy black. You will need approx. 2 cans to ensure the entire hood is coated properly. Thanks. Read More...
Beth July 01, 2012 for Model Number FRT21IL5DWO How many cans of the black spray paint will it take to cover my white frigidaire refrigerator?
1 Answer Beth, If you do this right, you'll need three 12 oz. cans of paint. Wash all the exterior surfaces with TSP, (Tri-Sodium Phosphate), rinse well with water. Sand all the surfaces with a medium grit sand paper and wipe all the surfaces with a "tack wrag". Apply the first coat of paint with a side to side motion and allow 30 to 40 minutes to "flash dry". Apply the second coat of paint with an up and down motion and allow the flash dry. These two coats are "base" coats and don't have to be "perfect". The next coat is the finish coat, so it does have to be "perfect" so take your time on this one. Good Luck and Thanks Read More...
Adam June 07, 2012 Is one can enough to paint two coats on a drop-in oven, and would a light touch-sanding need to be performed before applying this paint?
1 Answer Hello Adam. It depends on the size of the oven, but I would purchase 2 cans of paint 285006 to be safe. You should not need to sand the unit to paint it unless it is rusted out. Read More...