Phoebe M. August 19, 2013 for Model Number Magic Chef CGR3725ADW Will the no. 3412D024-26 work on the power burst burner of my magic chef range Model #CGR3725ADW?
1 Answer Hello Phoebe! Your range uses one burner part number WP3412D021-09 and three burners part number WP3412D024-09. Thanks. Read More...
Sam S July 20, 2013 for Model Number 31213WAV What is the red seal that goes between the burner head and the stove top? Mine are broke in pieces.They almost look like the rubber seal you use on canning jars.
1 Answer Sam, The red seal is just the burner gasket. The part is no longer manufactured as the manufacturer determined it was not required. Read More...
1 Answer Melodie, according to your model number the replacement burner head is part number WP3412D024-26. Thanks! Read More...
Tom June 21, 2013 for Model Number MGR5745ADA The spark igniter on the rear left isn't working properly. To replace that burner, would I choose Part Number: AP4416934
1 Answer Tom, Yes, burner head part number 3412D024-28 is the correct burner head for your unit. Read More...
Scott T. May 18, 2013 for Model Number 3468XVA What burner heads do I need for my stove? The right front and left back burners are high speed burners.
1 Answer Scott, according to your model number 3468XVA the unit uses four burners, part number WP3412D024-09. Thanks. Read More...
Thomas C. April 29, 2013 for Model Number MGR4452BDQ The burner I need to replace is the Power Boost burner (front right) but I am unsure which of the two shown would be the correct part?
1 Answer Thomas, the right front power boost burner is part number WP3412D021-09. Thanks! Read More...
Jaime C February 08, 2013 for Model Number Maytag Model MGR5710ADQ My burner is beige color and looks like as in P/N AP4416934. Question; What is the different in Burner Head P/N AP4416934 and Sealed Burner Assy P/N AP4394705?
1 Answer Hello Jaime, The only difference of the two burners may be the btu output that it can accept. 3412D024-28 is the burner that your unit calls for. Read More...
Clarence A December 29, 2012 for Model Number Maytag/ Gas top burner IgniterCHG9800BAM I have a maytag Gas stove model chg9800Bam. It seems when cleaning the top burner area, the cloth catches on the Burner igniter and brakes the porcelain protector. In order too repair I am forced to buy the entire burner unit. I have a total of four burners that are in excellant condition with out a working igniter. At a price of Fifty Dollars per Burner I would like to buy four of the Igniters only ? PS I was in the commercial Kitchen repair Business for 35Yrs. So I repair of my own.
1 Answer Hello Clarence, Unfortuneately the ignitors are part of the sealed burners and cannot be replaced individually. You would have to replace the sealed burner heads 3412D024-28. Read More...
Mike January 19, 2012 for Model Number mgr5750obdw The power boost burner has an excessive flame with black soot, will replacing just the burner fix the problem ?
1 Answer Hi Mike. Remove the power and remove the burner. Is this the only burner doing this ? Un hook the burner igniter and set the burner aside. Then use a deep socket to take the orifice all the way down against the inner jet until It lightly stops. COUNT AND RECORD THE # OF TURNS. Then remove the orifice hood completely. Use a small safety pin to insert in the top and check for any blockage. Now then concentrate on the lower jet assy. to make sure there are no debris there also. You did not say which gas product you are set to use. The unit is normally sent from the factory w/ Nat- gas. If it is to be used under L.P. then you need to fully convert it.Then reinstall the burner hood the exact # of tirns counted previously. The normal amount of turns from bottom out is 1-1/2 to- 2 turns for Nat-gas set up. All the way bottomed for LP- gas. Black soot sounds like a bad pressure regulator or a bad conversion if all the burners and oven are doing the same.....? Let us know so we can assist. further. Thank You. Read More...
Pam January 11, 2012 for Model Number MGR5750ADA Are burners AP4416934 interchangable with the Maytag range model #MGR5750ADA without having to do other upgrades? (Wires, etc.) Or can the original burners be used without the rubber gaskets that are no longer available?
1 Answer Hello Pam! Yes, the original burners can be installed on the appliance without the gaskets. The burners should be a direct replacement. If you need any install help please let us know. Thanks! Read More...