Julie January 10, 2019 Hi, I bought replacement parts to replace the door on my Maytag MAH-24 washer because the old one cracked and would not stay on the hing. so I bought the new door parts and took the door apart. Now I do not know how to put the door back together. I need a diagram or instructions. the model number of the unit is MAH2400AWW. Thanks!
1 Answer Julie, I have sent you an email with instructions on door removal so just reverse the steps, hope this helps. Read More...
Joe July 22, 2015 for Model Number MAH2400AWW Instructions on how to put spring loaded handle and trim plate back together on maytag front load washer model MAH2400AWW.
1 Answer Hello Joe. 1. Disconnect power supply to unit. 2. Remove Door Assembly 3. Remove screws on door inner panel. 4. Remove pin through door strike. 5. Unsnap handle from retainer. Reinstall in reverse order. Read More...
Perr March 11, 2013 for Model Number FTB4000FS1 I need the door handle and outside glass for this model washer. I am looking at part Number 34001178 (AP4044207) replaces 34001178. Is this the correct outer door for my washer. The inner door is not cracked, no water leaking. I just need plastic on the outside, and door handle. Thanks Perry
1 Answer Hello Perr, The model number listed is not showing as a valid model number. Please verify the model number. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Paul D January 28, 2013 for Model Number MAH2400AWW I have the Maytag front loading 24 inch washer, Model MAH2400AWW. The upper portion of my door cracked and no longer holds on the upper door hinge. The glass and other parts are OK. Is this frame the only part I need to fix the door so it will hang correctly on the hinge again? Thanks, Paul
1 Answer Paul, you will need to inspect the glass holder WP34001179 and the door cover WP34001178 and replace the broken part. Thanks! Read More...
Mike August 23, 2012 for Model Number mah2400aww How do you get the old glass out of this holder. As I was taking the door apart all the pieces fell out. Needing instructions on how to put the spring loaded latch back into the door handle.
Pb July 26, 2012 for Model Number Maytag front load washing machine I need to replace plastic cover door, part #34001178, on Maytag front load washing machine. What's the instructions for doing so?
1 Answer Hello PB. We will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Ronda October 06, 2011 for Model Number MDE2400AZW My dryer has no heat. I have been reading some of the other questions regarding the element and/or fuses. It's all very confusing to me as I have never done this before. Can you please help me on where to start and what exactly I am looking for?
1 Answer Hello Ronda. Check and make sure the proper voltage is coming to the dryer. Check and make sure the unit is not set to Air Fluff. Also check the heater 34001073 and thermal fuses WP35001021 WP35001022 and see if they are good. You can test these with a multi-meter MA-DM1. They should read closed for continuity. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Ronda October 06, 2011 for Model Number MAH2400AWW I leaned on the door. The plastic cracked and the top part of the hinge came out of the door. Can I just replace the outside piece of the door that the hinge goes in to? The door opens from the right ( hinges are on the left) I only see doors here that open from the left. Do you have a door that opens from the right?
1 Answer Hello Ronda. The door cover WP34001178 is the outer plastic piece of the door, and it is reversible for right or left side hinges. Hope this helps. Read More...