George May 23, 2017 for Model Number JES8850BAS I bought the oven light assembly and can get the old one loose by removing one screw but can't seem to get the plastic connector out of the small opening. Help.
1 Answer George, If you cant "fish" the connector out or through the opening in the cavity, you may have to raise the cooktop and access the wire harness and cover to dismantle and access the connector. Read More...
George T May 23, 2017 for Model Number JES8850BAS I have purchased the light assembly AP6011238 and have removed the screw of the old one, but can't get it the large plactic connector out of the tiny opening in the wall of the stove. What's the trick?
1 Answer George, You will most likely need to pull the unit out from the wall and remove the rear wall of the unit in order to get the connector through. Read More...
Neil December 10, 2016 for Model Number JES8850BCB Whats the bulb light model? I suuposed I just can buy it anywhere available in a hardware store?
1 Answer Neil, The part number that you will need for the light will be part number WP74011220. The bulb is not available as a separate part. Read More...
Shari January 19, 2016 for Model Number JDS9860AAW My light in the oven does not have the flange that is on the replacement part. Will it still work? Thanks, Shari
1 Answer Hello Shari. We will need your serial number to help you with this. Please call 1-877-477-7278 or post your model and serial number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Jerry January 13, 2016 for Model Number JDS9865BDP Can I just pop off the glass on the halogen oven light enclosure unit and replace just the bulb? I have a replacement bulb. Thanks
1 Answer Hello Jerry. Sorry, the manufacturer does not recommend taking the light assembly apart. Read More...
Caroll R November 25, 2015 for Model Number JES8850BAS Im curious if you can get just the replacement bulb or you have to get the whole assembly. If I can get just the bulb where do I purchase the bulb?
1 Answer Caroll, Unfortunately the light bulb cannot be purchased separately and you will need to replace the halogen light assembly WP74011220. Read More...
Lindsey February 17, 2015 for Model Number JDS9860AAP I am easily able to pull the glass cover off. That part is easy. How do I remove the metal case/wiring component?the screw that holds it in is hidden behind wall of the oven. Please help provide guidance.
1 Answer Lindsey, You will have to move the range out of the cabinet opening " 1. Remove power from unit. 2. Open oven door and locate oven light. 3. Grasp lens cover and pull outward on one side to gain access to bulb. 4. Carefully remove old bulb, by lifting bulb straight out of ceramic base. NOTE: To avoid damaging the new bulb and decreasing life of the bulb, do not touch new bulb with bare hands or fingers. Hold with a cloth or paper towel. NOTE: Proceed with the following steps for oven light socket removal. 5. Remove unit from installation position. 6. Disconnect or unplug the power cord leading from unit to fuse box or junction box depending on unit. 7. Carefully displace fiberglass insulation away from rear of light socket. 8. Release metal tabs on light socket and push socket assembly away from the oven cavity. 9. Label and disconnect wires from light socket. 10.Reverse procedure to reinstall light socket. Reposition insulation around lamp socket. NOTE: Reposition fiberglass insulation around light socket to eliminate the possibility of any heat related problems." Read More...
Nj October 22, 2014 for Model Number jes9900bcw I received the light assembly # 74011220 for my jenn air. I pulled the burnt out one out a bit. Do I need to lift the glass top off to complete? NJ
1 Answer Hello NJ. Oven Light Bulb/Oven Light Socket Replacement The light automatically illuminates when the door is opened. The light will not operate during a clean cycle. 1. Remove power from unit. 2. Open oven door and locate oven light. 3. Grasp lens cover and pull outward on one side to gain access to the bulb. 4. Carefully remove old bulb by lifting bulb straight out of base. 5. When installing the new bulb, place cover over socket so the cut-out in the glass cover aligns with the base on the socket. NOTE: To avoid damaging the new bulb and decreasing life of the bulb, do not touch new bulb with bare hands or fingers. Hold with a cloth or paper towel. NOTE: Proceed with the following steps for oven light socket removal. 6. Remove power to unit. 7. Remove screw securing light socket to oven cavity. 8. Label and disconnect wire terminals from light socket. 9. Reverse procedure to reinstall light socket. NOTE: Reposition fiberglass insulation around light socket to eliminate the possibility of any heat related problems. Read More...
Ray October 21, 2013 for Model Number JDS9865BDP22 Ray M for Model Number AP4100082 Answer Hello Ray. Remove the screw securing the housing and tilt forward and pull out wires and unplug the assembly. I followed the instructions and replaced the lamp assembly. Unfortunately I cannot get the light to shut off. The light button buzzes when pressed the door plunger goes in and out but the light stays on. Could I have plugged the light in backwards or is there another problem I have overlooked? Read more: http://www.appliancepartspros.com/whirlpool-light-asy-hal0gen-74011220-ap4100082.html#qa1#ixzz2iPdcAZVV http://www.appliancepartspros.com
1 Answer Ray, There is not a certain way that you would need to plug in the lamp. You do want to check to make sure that the wires are not touching metal and completing the circuit. Other than that the issue would be in the control board. Read More...
1 Answer Hello Ray. Remove the screw securing the housing and tilt forward and pull out wires and unplug the assembly. Read More...