Greg September 22, 2017 for Model Number WTW6200SW3 The power button does not work all the time. The washer appears to have no power , reset and keep trying and eventually comes on this happens frequently but not always.
1 Answer Greg, You will want to check the ribbon harness that connects to the main board. Check for corrosion and if this checks ok then would most likely be a faulty control board. Read More...
Mike L. May 27, 2017 for Model Number WTW6600SW2 Nothing happens when I try to start my Cabrio washer, it just hums. No matter which cycle I put it in it doesn't start. The lid will lock, and the minutes show, but nothing else happens. I then have to unplug the washer to turn it off. What's wrong?
1 Answer Hello Mike, You will need to pull the tech sheet by raising the main top and retrieving it from the plastic zip lock baggy affixed to the inside of the front panel. Use this to pull the fault codes from the control. This will point you in the correct direction for a proper diagnosis. Read More...
Asif April 01, 2017 for Model Number WTW6600SW2 In normal cycle machine get little water than doing nothing., did diagnostic no fault code logged in, start automatic test stuck in C1 keep bringing in water non stop so had to stop the machine. Not sure board issue or inner basket stuck, BTW rinse and drain cycle ok. Thank you in advance,
1 Answer Asif, With the unit overfilling with water then this sounds like it would be caused by a pressure switch whiich is part of the board. Read More...
Lisa October 13, 2016 I just replaced the lid lock mechanism a few months back. This machine is telling me the lid isn't locked still. It will not run or turn off without unplugging the machine. What could be wrong. Super frustrated with this washer.
1 Answer Hello Lisa. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Rmacfadzen August 06, 2016 for Model Number whirlpool cabrio After the wash is finished and in the dryer, the washer started beeping and wouldn't shut off, even after unplugging, no lights came on, no codes, just beeping, and that was 20 minutes after the wash came out. Husband smacked quite a few times and it finally quit. Suggestions?
1 Answer Macfadzen, The most probable issue is the user interface board and encoder assembly. A model number would have been a big help, We could supply the part number you may need, as well as some appropriate test information to help pinpoint the problem. You can find the tech data sheet taped to the inside of the washer cabinet, on the front panel(if it hasn't been removed or lost) and can program the control and review the error codes, and test the washer components to get a better idea of what is wrong, and what direction to take. You can also re post your question, with a model number and we'll be happy to supply the information needed. Thanks, Read More...
Renzo July 16, 2016 for Model Number Whirlpool Washer WTW6200WV0 Hi: My washing machine won't spin indicating unbalance load UL. When I did the trouble shooting according to the manufacturer, it shows F70. I just replaced the Rotor Position Sensor (WPW10178988), but it is still the same. Thanks, Renzo
1 Answer Hello Renzo. It sounds like you will need to order and replace the suspension rods on the unit. Read More...
Keaton June 22, 2016 for Model Number MTW6600TB0 My Maytag Bravos MTW660TB0 will no longer respond to any button I push on the control panel. If it power cycle the machine, then hold down the pause/cancel button for a few seconds, then hit the Power button, I regain control, but the washer is still not functioning properly. I pushed and held the pause/cancel button to abort the cycle and drain the water, but it doesn't work. With the water in the bottom of the tub, I was able to set it to "spin", The cycle seemed to start, the lock lid function activated, and the aggitator spun slowly back and forth very, but the countdown timer did not move. I walked away for a few minutes and came back to a completely full washer (water to the top), and the code on the display was 5d (suds detected), but this doesn't make sense because there are no suds and we only use Tide HE detergent. Is there a way to confirm that the logic board has an issue before I purchase a new one and replace it? Might this issue be something other than the control / logic board? The logic board is about a $300 part (W10130544), so I would like to try to make certain before I buy it, and I would like to purchase a new one from some place where I can return it if it is not the issue. Thanks!
1 Answer Hello Keaton. It sounds like you need to order and replace the control board WPW10051092 on the unit. Read More...
Pat February 25, 2016 for Model Number WTW6600SW2 My machine worked fine yesterday and this morning it would not even light up. I checked the outlet and it works. What could be wrong?
1 Answer Pat with the unit having no lights coming on then you will want to check the ribbon harness from the console to the control board is fully seated with no corrosion. If this checks ok then the issue will most likely be a faulty user interface which is part number WP8564290. Read More...
Jim December 20, 2015 for Model Number 11027072600 I need to know how to reprogram a new main control board after installation.
1 Answer Hello Jim, This units' tech sheet does not show that the control has to be programmed but a diagnostic test mode should reset everything to factory default but if the programming has been lost. If there is still a problem, the issue is most likely a connection issue or a failed control board WPW10189966. Read More...
Sam December 17, 2015 for Model Number WTW6600SW2/whirlpool My washer is around 8 years old. Recently it is showing "SD" code on screen at the end of drain cycle. I cleaned all lines including soap dispenser. What is your suggestion?
1 Answer Hello Sam. If your getting the code and the unit is not draining properly, you will need to order and replace the drain pump W10536347 on the unit. Read More...