Jeff C. April 28, 2019 for Model Number WTW6200VW0 Lf flashes. Replaced valve after it started leaking. I just get LF.
1 Answer Hello Jeff, you'll want to make sure the pressure hose and air dome is clear of any obstructions as well as any holes. If all is good, check your inlet hoses screens to make sure they are not clogged as well, if all is good you might have to replace the main board WPW10189966, hope this helps! Read More...
Mike January 31, 2019 for Model Number WTW7300DW0 I have a whirlpool cabrio washer. The codes F3 E6 came up. The buttons make no sound now and 52 minutes just show up on the screen. Thinking control board because I have had this problem in the past 3 years ago
1 Answer Mike, the error code F6E3 is the main control cannot hear the user interface, a communication failure. Check your connections, if you have a multimeter, check the continuity of the wires that run from the UI to the control. If that checks out ok, replace the UI, part number is W11102318 Read More...
Adeline September 28, 2018 If the control board goes bad on my cabrio washer will I still be able to do a manual test?
1 Answer Hello Adeline, It is doubtful that the manual testing can be accessed if the control board has failed. Read More...
Jenny August 27, 2018 My Whirlpool Cabrio (WTW6600SW2) displays error code F54. It seems to pass all of the automatic diagnostic tests and rotates freely (no friction). I replaced the RPS but it did not fix the problem. What are the next steps?
1 Answer Jenny, I sent you a tech sheet for the washer.Start at page 4 test # 3 and work thru the tests. Read More...
Michael June 04, 2018 My 110.27072600 stopped working - no response when the power button is pushed. There was a beep when I plugged it in, so I replaced the control board. Now I get four quick beeps but still no sign of life. I have rechecked the connections to the control board.
1 Answer Michael, With there being no display coming up then this would most likely be an issue with the user interface WP8564374 as long as the main control board has power coming into it. Read More...
Robert Allsop May 25, 2018 for Model Number MVWB300WQ0 During the spin cycle with or without clothes the machine it will goes off on the uL. (Around 6 to 9 minutes remaining) Plus it sounds like coins are rolling around inside the tub. Also under the machine it looks like something was spraying brown colored dirt on the inside of the machine, the floor plus the white cover for the motor.
1 Answer Robert, The "sounds like coins are rolling around inside the tub" could be coins between the tubs, but the "UL" code, " brown colored dirt on the inside of the machine, the floor plus the white cover for the motor." and the noise, would most likely be a failed/leaking tub seal and a damaged set of tub bearings, To rebuild the tub, order the bearing and tub seal kit W10435302 and the bearing installation tool W10447783, and you'd probably need the RPS sensor WPW10178988 once you check and clean the stator and rotor assembly(s). Read More...
Chuck March 10, 2018 for Model Number mvwb835dw1 drn displayed every time now. warranty technician came out and everything worked fine. next day drn.display. hose and pump are fine. i even checked for obstructions pulled all hoses and all clear. then sometimes it works for one load then usually it dont
1 Answer Chuck, With the pump and hose being fine then this will be an issue with the main control board. Read More...
Marko January 26, 2018 for Model Number 110.27086604 I replaced rps and harness kit and the motor stator I'm still getting code f51
1 Answer Marko, For this issue with the RPS sensor and the harness having been replaced then this will be a faulty main control board. Read More...
1 Answer Hello Vicki. You need to order part numbers W10435302 and W10447783 to repair the unit. Read More...
Selfie September 27, 2017 for Model Number #WTW6200VWO I 'NEVER' overload my washer; but each cycle I've tried, does not agitate. The machine fills, then times jumps from a 47min. down to a 15 min. It skips the wash and rinse cycles and goes to spin. When done I get an oL. It drains the water, but clothes are still wet. The 'Drain & Spin' cycle DOES work. My question is, "Do I need to replace the control board?"
1 Answer Hello Selfie. No, check for Mechanical friction on drive mechanism, not allowing the basket to disengage. Make sure the inner basket moves freely. Read More...