Steve July 20, 2015 for Model Number ed22pexhw02 Replaced water inlet solenoid valve water not stopping dripping into ice bin.
1 Answer Hello Steve. It sounds like the icemaker is leaking and you will need to replace the icemaker. Read More...
John April 22, 2015 I have a whirlpool side by side refrigerator model# ED22PEXHW02. The Ice maker leaks and water flow from the water dispenser is not as strong as it should be. Will this part work for a refrigerator with ice and water dispenser in front door?
1 Answer John, Yes the water inlet valve part number 2206123 is the correct water valve for your unit. Read More...
Rick April 03, 2015 for Model Number ED25PEXHW01 Replaced water valve 2206123 with new. Watre out of dispenser but not to ice maker. Tubes not frozen. Ice maker is new also and cycles fine. You mentioned in a previous answer that the wiring may need to be reversed. Is there any literature (hand drawn pictures will work) that shows/explains EXACTLY how this new water valve is supposed to be wired (detailed) and plumbed (detailed). I have searched for videos on this valve but none found that are exact. Thank you
1 Answer Hello Rick, You may have a harness issue. You will need to force an icemaker cycle by jumping 120Vac from terminals "T" and "H". Near the end of this cycle, you will need to see 120Vac on the wires to the water valve with the 1/4 inch water line that leads to the icemaker. If not, the issue is either a poor connection, a broken wire, or a defect in the icemaker, (new parts can be defective). As a note, this is an ac circuit and reversing the wires will not affect the operation of the water valve solenoid. Read More...
Dan February 14, 2015 for Model Number ED25UEXHW01 My water dispenser and ice maker are working, but the plastic part where the water line attaches is leaking (the part in the video he says will not be replaced...). I am willing to replace everything, but I need that part as well. Can you help?
1 Answer Dan, The 2206123 Water Inlet Valve, will have all three solenoids including the isolation solenoid and the brass connector for the water supply line. You'll have everything you need except a razor or sharp blade to trim the end of the water tubes so they seat and lock properly inside the john guess fittings. Read More...
Tim December 23, 2014 for Model Number Model #106.50532101 I have replaced the old inlet water valve and replaced with Part #2206123. Water dispenser is now working which is good. However, now when ice maker cycles on water comes out the water dispenser. Help!
1 Answer Hello Tim. Check and see if any of the water lines are reversed on the water valve and installed in the wrong spot. Read More...
Clark December 20, 2014 for Model Number 59212990 I have installed a new water inlet valve (part #2206123) on the Kenmore Model #59212990. However I still have the same problem, no water coming out of the water dispenser on the door. Before I installed the new valve, I had water going to the ice maker just fine, not sure now. I know that there are two connections for a 1/4 hose and 2 connections for 5/16 line, can you tell me which hose goes where. From the videos that I have watched it looks like the 1/4 hose that comes down the back of the refrigerator goes on the bottom 1/4 connection. Is that correct?
1 Answer Hello Clark, If your model number is 106.59212990, the 1/4 inch line goes up the back to the icemaker. The most obvious cause of no water is either a frozen water reservoir or a frozen water line in the door. Heat the water reservoir with a hair dryer for about 15 minutes. If this corrects the issue, set the fresh food compartment to a colder setting to increase air circulation so the cold air will not settle to the bottom of the fresh food compartment. Read More...
Denny October 05, 2014 for Model Number 106.53504300 I replaced ice maker(106 626662), filter and the inlet valve (2206123)on my Kenmore side-by-side(106.53504300). I still am not getting water coming into the cube tray. I was vary careful to put all the electrical and waterlines on as they came off the old one. Water does flow through fine to the water despenser. Is there some way to reset it so it will work as intended?
1 Answer Denny, Since the water valve was replaced and a new filter put in, you will want to check the fill tube coming into the icemaker to ensure that there is no ice build up in it. If this is clear then you will need to check the icemaker module by removing the cover of the icemaker and remove the 3 screws holding the module in place. Once this is done you will need to turn the module over and look for burn marks on the lower right side of the module. If burnt you will want to replace the icemaker and if not then check the wheel of the front of the module to see if the pins in the center are broken. If so then replace the module. There is no reset. Read More...
Vanessa September 02, 2014 for Model Number Estate Fridge TS22AE Icemaker not making ice. Sometimes little water and sometimes it over flows. You can hear when water shuts off it makes a loud noise. Is it the water intake value?
1 Answer Hello Vanessa. If the noise is coming from the water valve then it is the valve that needs to be replaced. Read More...
Jeff August 03, 2014 for Model Number 10653502300 I'm getting too much water when the ice maker fills up. When I adjust the timer, it doesn't change the length of time it fills. I'm thinking the ice maker is bad but I'm not sure. I've also checked the water inlet valve. How many ohms should water inlet valve #2206123 be pulling? I'm getting. The inlet solenoid is pulling 350, the green solenoid is pulling 175, and the purple is pulling 350. Does this mean the inlet valve is good? The water pressure going into the inlet valve seems to be fine. I've read through research that whenever you get too much water, it is either the ice maker, the water inlet valve, or the pressure coming in.
1 Answer Hello Jeff. If the unit is powering the valve to long, you will need to replace the icemaker 4317943. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Sanja V July 03, 2014 for Model Number Part 2206123 After replacement inlet water valve I have water dipenser working fine but in plastic pipe what going to the top of refrigerator I don'tse water coming. Maybe I didn't connect properly.where I can see where I need connect that plastic pipe.
1 Answer Sanja, The water tube that goes up the back of the unit would be for the icemaker and if the icemaker has not cycled then it will not have water in it and you not necessarily will see the water running through the tube. Read More...