Parts for Frigidaire CRA073PU10: 03 - Recommended Spare Parts

This electronic control board manages the appliance's user interface and core electronic functions so the unit responds correctly to button presses and cycle selections. Replacing a faulty board restores normal electronic control. What it does:

• Controls the display, touchpad/buttons, and cycle selection logic
• Manages power sequencing and electronic signals between modules
• Can stop or prevent operation if the board fails or detects faults
• Common symptoms include unresponsive controls, blank or erratic display, or appliances that won't start

• Disconnect power to the appliance before starting any work
• Handle the board carefully to avoid static discharge or physical damage
• Verify this part number matches the board in your appliance before installing

This overload protector is a refrigerator compressor safety device that helps prevent compressor overheating and electrical overloads, protecting the cooling system and helping restore normal compressor operation when conditions allow. What it does:

• Interrupts compressor power if the compressor overheats or draws excessive current
• Helps stop compressor damage from thermal or electrical stress
• Commonly used when the compressor hums but won't start, or when the fridge cycles on/off rapidly
• Works with the compressor start/relay assembly to ensure safe start-up and operation

• One overload protector

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the part
• Handle compressor terminals and wiring carefully; avoid bending or stressing terminals
• Replace the start relay at the same time if recommended by diagnostics

This replacement plug/cap seals an unused opening or access hole on compatible Frigidaire appliances to stop drafts and moisture while keeping internal components secure. It restores a finished appearance and prevents debris from entering. What it does:

• Seals access holes or service openings to help prevent water or air intrusion
• Secures wiring or tube routing by closing unused ports
• Helps keep out dust, pests and debris from internal compartments
• Common symptoms indicating replacement: missing or loose plug, visible gap, or water/draft at the opening

• One replacement plug/cap, as shown

• Disconnect power to the appliance before beginning any work
• Typically installs as a press-fit or snap-in component; no special tools required
• Inspect surrounding area for damage before installing; do not force into place

This replacement grille restores the exterior venting and finished look of the appliance, covering internal components while allowing airflow. It helps maintain proper ventilation and improves the unit's appearance. What it does:

• Covers and protects underlying components while providing venting for airflow.
• Prevents debris from entering the appliance interior through the vent area.
• Restores the appliance's finished appearance when the original grille is cracked or missing.
• Common symptom: visible damage, holes, or missing grille exposing internal parts.

• One replacement grille.

• High-level install usually requires removing a few screws or tabs; use a screwdriver or trim tool as needed.
• Disconnect power to the appliance before servicing if removal exposes electrical components.
• Handle carefully to avoid scratching the finish; retain any original clips or screws unless replacement hardware is provided.

This sealing plug caps an access hole or opening to prevent leaks, debris entry, or airflow in the appliance. It restores a finished seal and helps keep internal components protected from moisture and dirt. What it does:

• Covers and seals an unused service or access opening to prevent water and dirt intrusion
• Keeps loose parts and debris from falling into internal compartments
• Helps maintain proper airflow routing and prevents rattling from an open hole
• Commonly needed if the original plug is cracked, missing, or brittle

• Disconnect power and water before servicing the appliance
• Verify correct plug orientation and push fully into the opening until seated
• Replace any damaged retaining clips or surrounding gaskets to ensure a proper seal
• If the hole is deformed or the plug does not seat securely, stop and confirm correct part before continuing

This replacement exhaust hose vents hot discharge air from a portable air conditioner through the window kit, restoring proper airflow and cooling performance when the original hose is cracked, collapsed, leaking, or missing.

• Directs hot air from the unit to the outdoors via the window panel
• Helps maintain correct airflow and cooling efficiency
• Replaces a damaged, brittle, or collapsed vent hose
• Symptoms may include poor cooling, warm air leaking into the room, or the hose detaching

• Unplug the unit and allow it to cool before service
• Remove the old hose from the rear outlet and window panel couplers
• Seat and lock the new hose fully onto each coupler per your model's design
• Route the hose as short and straight as possible; avoid kinks or sharp bends for best airflow

This hose-to-window adapter links your portable air conditioner's exhaust hose to the window panel for proper venting. Replacing a damaged or missing adapter helps restore a secure connection and reduce warm air leakage at the window.

• Connects the exhaust hose to the window kit opening for correct venting
• Helps create a snug seal to direct hot air outdoors
• Can help with a hose that won't attach or stay secured at the window
• Useful when the original adapter is cracked, warped, or lost

• Power off and unplug the unit; allow it to cool before servicing
• Attach the adapter to the exhaust hose per your model's connection style (twist-lock/tabs)
• Seat the adapter into the window panel opening and ensure a tight seal
• Verify the hose is unkinked and the window panel is properly installed per the user manual