Parts for Frigidaire CRA083AT714: 03 - Recommended Spare Parts

This air filter features a durable plastic frame and screens airborne particles from intake air to help protect internal components. Replacing a cracked or heavily clogged filter helps maintain proper airflow and keep the appliance running efficiently. What it does

• Captures dust and lint from incoming air to reduce buildup inside the unit
• Helps maintain airflow and overall system efficiency
• Replaces a missing, damaged, or saturated filter
• Common symptoms: weak airflow, longer run times, visible dirt buildup or damage to the filter

• 1 air filter with plastic frame

• Disconnect power to the appliance before servicing
• Open the front grille or filter access panel per your owner's manual
• Slide out the old filter and insert the new filter in the same orientation
• Ensure the filter is fully seated; do not operate the unit without a filter

This louver is the front vent trim piece that directs airflow and covers the vent opening for a clean, finished appearance. It restores proper airflow pattern and replaces cracked, broken, or missing vent trim. What it does:

• Directs and channels airflow from the appliance vent for more consistent cooling or exhaust
• Covers and protects internal components from debris while maintaining proper ventilation
• Restores the appliance's finished appearance by replacing damaged or discolored trim
• Helps reduce drafts and unwanted light through the vent opening

• Disconnect power to the appliance before beginning any repair
• Inspect mounting tabs or screw holes and use the original fasteners when possible
• Snap into place or secure with screws depending on model—align tabs carefully to avoid breakage

This replacement remote control restores convenient handheld operation of your appliance, letting you change settings and control basic functions from a short distance without opening the unit. Easy swap for a failed or missing remote. What it does:

• Sends control commands to the appliance so you can change modes, power, and settings remotely
• Restores normal remote response when the original remote is lost, damaged, or unresponsive
• Helps diagnose whether issues are remote-related versus appliance-related by verifying signal/send function
• Works only with compatible appliance models that use this OEM remote protocol

• Insert fresh batteries and test remote operation before installation
• Follow the appliance manufacturer's pairing or setup procedure if required
• If remote still does not operate the appliance, check battery orientation and replace batteries, then refer to the appliance's user manual
• Dispose of used batteries properly and avoid exposing the remote to moisture or extreme heat

This temperature sensor (thermistor) monitors fresh food/freezer temperatures and sends readings to the refrigerator control board so the appliance maintains consistent cooling. Replaces a failed or intermittent sensor to restore accurate temperature control. What it does:

• Senses interior temperature and reports it to the control board
• Helps the compressor, fans and defrost system run at the correct times
• Common symptom: fridge or freezer temperatures are too warm or fluctuate
• Common symptom: unit runs constantly or cycles erratically
• Common symptom: inconsistent cooling between compartments

• One temperature sensor (thermistor)

• Disconnect power to the appliance before attempting any repairs
• Handle the sensor and wiring gently; avoid kinking or stretching the lead
• Verify connector pins align and seat fully; some models use a simple plug-in connector

This defrost drain tube routes meltwater from the freezer/evaporator area to the drain pan, helping keep the cabinet dry and preventing leaks or ice buildup. Replace a cracked, clogged, or damaged tube to restore proper drainage. What it does:

• Channels defrost and condensation water from the evaporator/freezer to the main drain
• Prevents leaks and pooling inside the cabinet that can cause odors or ice formation
• Helps maintain proper defrost water flow when the original tube is cracked, split, or blocked
• Works with the existing drain system and grommets to resume normal drainage

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove interior panels as needed to access the evaporator/drain area; handle evaporator fins carefully
• Ensure the tube is seated properly in the drain fitting and any retaining clips or grommets are reused or replaced
• Clear any drain trough or drain hole blockages and test with a small amount of water after installation

Note: Due to a factory change, the replacement accordion does not include the frames.

Mounting hardware, screws