Parts for Frigidaire CRA103BT111: 03 - Recommended Spare Parts

This replacement filter helps capture airborne particles during normal operation, protecting internal components and supporting proper airflow and performance. Replace a damaged or clogged filter to keep your appliance working efficiently and safely.

• Traps dust, grease, and debris from the airstream to protect the blower and internal parts
• Helps maintain proper airflow for effective ventilation and performance
• Replace if the filter is torn, saturated, misshapen, or heavily clogged
• Common symptoms of a worn filter include reduced airflow, lingering odors, and increased fan noise

• Disconnect power to the appliance before servicing
• Allow hot surfaces to cool; wear cut-resistant gloves—edges can be sharp
• Note the orientation of the old filter and seat the new one the same way
• Restore power and verify airflow after installation

This replacement power cord restores AC power to compatible refrigerators by replacing a damaged or worn supply lead. It provides a direct, safe power connection so the appliance can run reliably. What it does:

• Replaces a frayed, cut, or otherwise damaged power supply cord
• Restores consistent power when the appliance will not turn on or has intermittent power
• Maintains the appliance's grounding connection for safe operation
• Prevents electrical arcing from exposed wiring or compromised insulation

• One replacement power cord

• Disconnect the appliance from the power source before inspecting or replacing the cord
• Install with the proper strain relief and secure fasteners to prevent pinching or pull-out

This replacement remote control restores convenient handheld operation of your appliance, letting you change settings and control basic functions from a short distance without opening the unit. Easy swap for a failed or missing remote. What it does:

• Sends control commands to the appliance so you can change modes, power, and settings remotely
• Restores normal remote response when the original remote is lost, damaged, or unresponsive
• Helps diagnose whether issues are remote-related versus appliance-related by verifying signal/send function
• Works only with compatible appliance models that use this OEM remote protocol

• Insert fresh batteries and test remote operation before installation
• Follow the appliance manufacturer's pairing or setup procedure if required
• If remote still does not operate the appliance, check battery orientation and replace batteries, then refer to the appliance's user manual
• Dispose of used batteries properly and avoid exposing the remote to moisture or extreme heat

This thermistor is the refrigerator temperature sensor that helps the control board monitor and regulate cooling. Replacing a failed thermistor restores accurate temperature readings for more consistent fridge and freezer performance. What it does:

• Senses internal air temperature and sends that information to the control board
• Helps the defrost and compressor cycles run at the correct times
• Commonly linked to symptoms like inconsistent temperatures, error codes, or a unit that runs constantly
• Does not control cooling directly but provides the temperature feedback the system needs

• Always disconnect power to the appliance before beginning service
• Typically located in the fresh food or freezer compartment near the evaporator
• Handle the sensor and wiring gently; avoid pulling on the wires or bending the probe sharply
• If troubleshooting, verify wiring and sensor resistance per the manufacturer's service instructions before replacement

Replacement evaporator fan blade that moves cold air across the evaporator coil and through the refrigerator compartments to help maintain even temperatures. Restores airflow to reduce warm spots and improve overall cooling consistency. What it does:

• Spins on the evaporator fan motor to circulate cold air through the freezer and fresh-food sections.
• Restores proper airflow when the original blade is cracked, warped, or broken.
• Common symptoms prompting replacement: reduced or uneven cooling, rattling/scraping noises from the freezer, or visible blade damage.
• Helps prevent excessive frost buildup by maintaining steady airflow over the evaporator.

• Disconnect power to the appliance before beginning any service.
• Handle the blade carefully; edges and broken pieces can be sharp.
• Ensure the blade is fully seated on the motor shaft and any retaining hardware is reinstalled per the OEM's guidance.

This retainer secures a mating component in your appliance so it stays properly aligned during use. Replacing a damaged or missing retainer restores a snug fit, reduces vibration noise, and helps prevent the attached part from shifting or falling.

• Secures the attached part to prevent movement and vibration
• Maintains proper alignment and fit within the assembly
• Failure clues: attached component is loose, rattles, sags, or won't stay in place
• Visual signs: retainer is cracked, deformed, worn, or missing

• Disconnect power to the appliance before starting; allow hot or moving parts to cool/stop
• Note the original orientation and position; take a quick photo for reference
• Seat the new retainer fully and transfer any original fasteners as needed
• Do not overtighten hardware; verify the held component is secure before reassembly

This window filler kit installs on the sides of a window air conditioner to close gaps between the chassis and the window frame. It helps secure the unit and limit air leaks, moisture, and pests from entering the room.

• Closes the left and right side openings between the unit and sash window
• Helps stabilize the air conditioner and reduce vibration noise
• Replaces cracked, brittle, warped, or missing side curtains/fillers
• Common signs: drafts or visible gaps around the unit; torn or broken accordion panels

• Disconnect power and support the air conditioner to prevent a fall
• Slide the fillers into the unit's side channels or mounting frames per your model's instructions
• Reuse the unit's hardware as directed; avoid overtightening fasteners in plastic components
• After installation, ensure the unit is secured and pitched for proper drainage per manufacturer guidance

Mounting hardware, screws