Parts for Electrolux FFRL0633Q11: 02 - Recommended Spare Parts

This replacement remote control restores convenient handheld operation of your appliance, letting you change settings and control basic functions from a short distance without opening the unit. Easy swap for a failed or missing remote. What it does:

• Sends control commands to the appliance so you can change modes, power, and settings remotely
• Restores normal remote response when the original remote is lost, damaged, or unresponsive
• Helps diagnose whether issues are remote-related versus appliance-related by verifying signal/send function
• Works only with compatible appliance models that use this OEM remote protocol

• Insert fresh batteries and test remote operation before installation
• Follow the appliance manufacturer's pairing or setup procedure if required
• If remote still does not operate the appliance, check battery orientation and replace batteries, then refer to the appliance's user manual
• Dispose of used batteries properly and avoid exposing the remote to moisture or extreme heat

This temperature sensor (thermistor) monitors fresh food/freezer temperatures and sends readings to the refrigerator control board so the appliance maintains consistent cooling. Replaces a failed or intermittent sensor to restore accurate temperature control. What it does:

• Senses interior temperature and reports it to the control board
• Helps the compressor, fans and defrost system run at the correct times
• Common symptom: fridge or freezer temperatures are too warm or fluctuate
• Common symptom: unit runs constantly or cycles erratically
• Common symptom: inconsistent cooling between compartments

• One temperature sensor (thermistor)

• Disconnect power to the appliance before attempting any repairs
• Handle the sensor and wiring gently; avoid kinking or stretching the lead
• Verify connector pins align and seat fully; some models use a simple plug-in connector

This thermistor is the refrigerator temperature sensor that helps the control board monitor and regulate cooling. Replacing a failed thermistor restores accurate temperature readings for more consistent fridge and freezer performance. What it does:

• Senses internal air temperature and sends that information to the control board
• Helps the defrost and compressor cycles run at the correct times
• Commonly linked to symptoms like inconsistent temperatures, error codes, or a unit that runs constantly
• Does not control cooling directly but provides the temperature feedback the system needs

• Always disconnect power to the appliance before beginning service
• Typically located in the fresh food or freezer compartment near the evaporator
• Handle the sensor and wiring gently; avoid pulling on the wires or bending the probe sharply
• If troubleshooting, verify wiring and sensor resistance per the manufacturer's service instructions before replacement

This overload protector is a compressor start-device that helps prevent compressor damage by interrupting power if the motor overheats or draws too much current. It restores normal operation when conditions return to safe levels. What it does:

• Senses excessive heat or current at the compressor and interrupts power to prevent motor damage
• Stops the compressor from attempting to start repeatedly when under stress
• Helps address symptoms such as a refrigerator that hums but won't run, frequent compressor cycling, or a compressor that runs briefly then stops
• Works with the compressor start relay as part of the motor protection system

• One overload protector

• Disconnect power to the appliance before inspecting or replacing the protector
• Located on the compressor body; replace with the same style and orientation for proper fit
• Handle the component and compressor terminals carefully to avoid damage

This replacement platform provides a stable base inside the oven cavity to support the oven floor and related internal components, restoring proper alignment and preventing sagging or rattling. What it does

• Supports the oven floor and internal components to maintain correct alignment.
• Helps stop movement, vibration, or rattling coming from the oven cavity.
• Restores a flat, secure surface for heating elements and cookware.
• Useful when the original platform is bent, warped, or cracked, causing instability.

• One platform.

• Disconnect power to the appliance before starting any repair to prevent shock.
• Remove oven racks and any mounting fasteners to access the existing platform.
• Installation typically involves repositioning and fastening the platform with existing screws or clips—keep original hardware unless replacements are specified.
• If the part is heavy or awkward, have a second person assist to avoid injury or damage.