Parts for Lg LSXS26366S: Refrigerator Compartment Parts

The Water Filter LT800P is an OEM part for LG refrigerators. This filter is designed to remove contaminants from the water supply, ensuring clean and fresh-tasting water and ice.

Causes of a bad water filter can include extended use beyond its recommended lifespan, exposure to high levels of contaminants, or damage to the filter itself.

Symptoms of a bad Water Filter LT800P include:

• Unpleasant taste or odor in the water or ice
• Reduced water flow from the dispenser
• Indicator light signaling the need for replacement
• Visible sediment or particles in the water

This OEM LG part is also compatible with Sears/Kenmore.

This insulated duct assembly cushions and channels airflow while reducing noise and heat transfer. It restores proper ventilation and helps maintain efficient operation and quieter performance. What it does:

• Replaces a damaged or worn insulated duct to restore correct airflow routing
• Reduces vibration noise and minimizes heat loss from the airflow path
• Helps prevent air leaks that can cause reduced performance or localized heating
• Fits where the original insulated duct was installed and works with the appliance's venting system

• Disconnect power and any gas supply before servicing
• Inspect surrounding seals and fasteners; replace any damaged clips or tape
• Follow OEM instructions for routing and securing the duct to avoid pinching

This is the drawer tray assembly that supports and guides a refrigerator storage drawer so it slides smoothly and holds items securely. Replacing a damaged tray restores proper drawer operation and usable storage space.

• Supports the matching drawer bucket and provides the slide/track interface
• Helps drawers open/close smoothly and sit level
• Common failure signs: cracked tray, broken rails or tabs, drawer tilting, binding, or falling off the track
• Restores stability to prevent items from spilling or jamming the drawer

• Disconnect power and remove food from the affected drawer area
• Pull out the drawer and lift it off the rails as directed in your model's manual
• Transfer any reusable hardware from the original tray if applicable
• Seat the new tray fully on the rails and test drawer movement before restoring power

This vegetable tray assembly replaces a damaged or worn crisper drawer to restore storage for fresh produce and help keep it organized in your refrigerator. Durable molded construction supports fruits and vegetables while sliding into the cabinet. What it does:

• Replaces a cracked, chipped, or broken crisper/vegetable drawer that won't hold produce
• Restores a smooth sliding drawer action when the tray and guides are intact
• Provides a dedicated, contained space to keep fruits and vegetables organized
• Helps prevent produce from spilling onto lower shelves

• One vegetable/crisper tray assembly

• Unload produce and remove the old tray before installing the replacement
• Inspect drawer rails/guides for damage and clean tracks of debris for smooth operation
• No special tools typically required; handle glass or plastic components carefully to avoid damage

This Tray Cover Assembly replaces a cracked or damaged plastic cover that protects and secures the appliance tray, restoring proper fit and appearance. It provides a simple, direct replacement for worn or broken covers. What it does:

• Covers and protects tray contents from debris and spills
• Keeps the tray seated and aligned to prevent rattling or shifting
• Replaces cracked, warped, or broken covers that no longer stay in place
• Helps restore proper function and appearance after impact or wear

• One tray cover assembly

• Disconnect power or unplug the appliance before starting any repair
• Remove the old cover by releasing retaining clips or screws as applicable; handle plastic parts gently to avoid breakage
• Align the replacement cover and snap or fasten it into place until all clips engage

This rear cabinet cover replaces a damaged or missing TV back panel to protect internal electronics and restore the set's finished appearance. It provides a secure mounting surface and helps keep dust and debris out of the chassis. What it does

• Shields internal circuit boards, power supply and connections from dust, impact and accidental contact
• Restores proper alignment and attachment points for the TV chassis and external connectors
• Eliminates rattles or loose fit caused by cracked or broken mounting tabs
• Helps maintain proper ventilation paths around internal components when installed correctly

• Unplug the TV and place on a soft, protected surface before starting; handle cover edges carefully to avoid cuts.
• Keep and reuse original screws and any attached hardware unless replacements are specified.
• Align mounting tabs and connectors before tightening fasteners; do not force or overtighten to avoid breaking plastic tabs.
• If internal access is required, refer to the TV's service manual; do not touch exposed boards while the set is powered.

This upper hinge assembly secures and guides the refrigerator's top door, restoring proper door alignment and smooth opening/closing. Replaces a worn or damaged hinge to help stop sagging, rubbing, or uneven sealing. What it does:

• Supports the top door and attaches it to the cabinet for stable operation
• Guides door movement so the door opens and closes smoothly
• Restores proper door alignment to improve seal and reduce rattling
• Addresses symptoms like a drooping or misaligned door, noisy hinge action, or doors that don't latch evenly

• Disconnect power (unplug the appliance) before starting any repair
• Support the door weight before removing the hinge to avoid dropping or damaging the door
• Basic hand tools typically required; follow OEM diagram for correct fastener locations and orientation

This water filter assembly secures the refrigerator's replaceable water filter and routes water to the dispenser and ice maker. Replacing a cracked or leaking assembly restores proper flow and helps ensure a tight, reliable seal at the filter connection. What it does:

• Holds and seals the replaceable water filter cartridge
• Channels inlet water through the filter to the dispenser and ice maker
• Helps prevent leaks at the filter connection and housing
• Common symptoms: leaks around the filter area, low or no water to dispenser/ice maker, filter won't seat or stay in place, visible cracks on the housing

• 1 water filter assembly

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure by dispensing water; place a towel to catch residual water
• Transfer fittings/lines carefully and seat connections fully; do not overtighten
• Restore water, check for leaks, and run water to purge air from the system

The Water Filter LT800P is an OEM part for LG refrigerators. This filter is designed to remove contaminants from the water supply, ensuring clean and fresh-tasting water and ice.

Causes of a bad water filter can include extended use beyond its recommended lifespan, exposure to high levels of contaminants, or damage to the filter itself.

Symptoms of a bad Water Filter LT800P include:

• Unpleasant taste or odor in the water or ice
• Reduced water flow from the dispenser
• Indicator light signaling the need for replacement
• Visible sediment or particles in the water

This OEM LG part is also compatible with Sears/Kenmore.

The Water Tank is an OEM part for LG refrigerators. This tank stores and supplies water to the refrigerator's ice maker and water dispenser, ensuring a consistent supply of fresh, filtered water. It is designed to fit securely within the refrigerator, maintaining hygiene and preventing leaks.

Over time, the water tank can become worn out, cracked, or contaminated. Common causes of a bad water tank include regular wear and tear, exposure to extreme temperatures, or damage from mishandling or improper installation.

Symptoms of a bad water tank include:

• Leaking water inside the refrigerator
• Low water flow to the dispenser or ice maker
• Unusual tastes or odors in the water
• Visible cracks or damage to the tank

This OEM LG part is also compatible with Sears/Kenmore.

Replacement tube connector (mechanical) that secures and routes tubing in compatible LG appliances, helping restore proper fluid flow and reduce leaks from loose or damaged connections. A literal OEM-style connector used where a secure tube-to-component join is required. What it does:

• Joins and secures tubing to appliance components or chassis to maintain a stable connection
• Keeps tubing aligned to prevent kinks or dislodging that can interrupt flow
• Commonly replaced when you see dripping, visible leaks, loose tubing, or poor water flow
• Fits the original mounting interface for reliable mechanical retention

• Disconnect power and shut off the water supply before starting any repairs
• Inspect tubing and nearby fittings for damage; replace any compromised tubing before installing the connector
• Seat the connector fully and secure per the appliance's service instructions; avoid overtightening which can damage tubing
• After installation, restore water and power and check the connection for leaks during a short test cycle

The Connector (Mech), Tube is an OEM part for LG refrigerators. It is used to securely connect water tubing within the refrigerator, ensuring a reliable flow of water to components such as the ice maker and water dispenser.

Causes of a bad connector can include wear and tear over time, physical damage from improper installation or handling, or degradation due to exposure to varying temperatures and water pressure.

Symptoms of a bad connector include:

• Leaks or drips around the connector area
• Reduced water flow to the ice maker or water dispenser
• Water pooling inside or around the refrigerator
• The ice maker or water dispenser not functioning properly

This OEM LG part is also compatible with Sears/Kenmore models.

This mechanical mounting band secures a bracket assembly inside the appliance to keep components aligned and reduce vibration. It restores proper bracket positioning so moving parts run quietly and reliably. What it does:

• Holds a bracket or component assembly in place to maintain proper alignment
• Dampens movement and reduces vibration-related noise or rattling
• Prevents excess wear by keeping parts from shifting during operation
• Helps maintain correct clearances to avoid interference or rubbing

• Disconnect power before inspecting or replacing internal parts
• Remove only the fasteners necessary to access the bracket; keep track of hardware
• Secure all fasteners to the manufacturer's torque or snug specification
• Replace the band if bent, cracked, or missing to restore proper fit and function