Parts for Frigidaire FRSC2333AS6: Refrigerator Door Parts

This gray magnetic refrigerator door gasket replaces the perimeter seal on the fresh food door. It creates an airtight closure that keeps cold air in, blocks humid air, and helps prevent temperature swings, frost, and condensation. What it does:

• Seals the door perimeter with a flexible magnetic edge to stop air leaks
• Helps maintain proper refrigerator temperature and reduce frost/condensation near the door
• Restores smooth closing when the old gasket is torn, shrunken, or warped
• Typical symptoms: visible gaps, moisture on the gasket, frequent cycling, or food warming near the door

• 1 gray magnetic refrigerator door gasket

• Disconnect power before servicing
• Warm the new gasket with a hair dryer or hot water to relax folds for easier seating
• Remove the old gasket; press/fasten the new gasket evenly into the door channel or retainer, ensuring corners are fully engaged
• Close the door and check for uniform contact; adjust hinges or gently reshape with warm air as needed and allow the gasket to set with the door closed

This dairy compartment is a replacement door bin designed to hold butter, cheese and other small refrigerated items, keeping them organized and easy to access. Restores a secure, covered storage area in the refrigerator door. What it does:

• Provides a covered bin for butter, cheese and small deli items to keep them contained and visible
• Replaces cracked, warped or broken door dairy compartments that no longer latch or sit properly
• Helps prevent spills and keeps items from shifting when the door opens and closes
• Matches original mounting pegs and track locations to restore proper fit

• Handle carefully to avoid damaging mounting pegs or the bin; inspect pegs and track before installing
• Remove existing bin by lifting/tilting per your model's method, then align and press new bin into the door track until it seats
• Clean the door track and surrounding area before installation for best fit

The Handle is an OEM component specifically designed for Frigidaire refrigerators. This door handle is located on the exterior front of the fridge, providing an ergonomic grip for easy opening and closing of the refrigerator door. 

Symptoms of a bad handle can include loose mounting, difficulty grasping or turning the handle, or physical damage rendering it unusable. 

Causes of a bad handle include wear and tear over time, damage from impact or harsh cleaning chemicals, or loose fasteners allowing the handle to wobble.

Symptoms of a bad handle include:

• Loose, unstable grip that cannot support door weight  
• Difficulty opening and closing the refrigerator door
• Damage to the handle mechanism, mounting bracket, or appearance

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace yours today before replacing becomes necessary.
 

This #10-32 x 3/4-inch machine screw secures appliance components such as panels, brackets, and handles. Using the correct length and thread helps restore a snug, rattle-free hold wherever this screw is specified by the manufacturer.

• Fastens components with a #10-32 machine thread and 3/4-inch length
• Helps keep panels, trim, brackets, or handles secured and aligned
• Replaces missing, stripped, or corroded hardware
• Common signs include loose or wobbly parts, rattling, missing screws, or damaged screw heads/threads

• Disconnect power before servicing; if working near a water connection, shut off the water supply
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping plastic or threads
• Reuse any model-specific washers or spacers if present

This door bushing kit replaces worn hinge bushings that keep refrigerator/freezer doors aligned for smooth, stable operation. Restores proper door rotation to reduce sagging, rubbing, and noisy or stiff hinges. What it does:

• Provides replacement hinge bushings that support the door on its hinge pin for correct alignment
• Helps stop door sag, scraping, and uneven gaps that let cold air escape
• Reduces hinge noise, sticking, and rough door movement
• Fits into the door hinge assembly to restore smooth pivoting action

• Always unplug the appliance or disconnect power before starting repairs
• Support the door while removing hinge pins to prevent dropping or damage
• Remove old bushings from the hinge housing and press or snap new bushings into place; reassemble hinge and confirm alignment

The Door Shelf Bin is an OEM part for Frigidaire refrigerators. This bin is designed to attach to the interior of the refrigerator door, providing convenient storage for items like condiments, beverages, and other frequently used food products.

Causes of a bad door bin can include overloading the bin with heavy items, accidental impacts from closing the door too forcefully, or general wear and tear over time. These factors can lead to cracks, breaks, or warping of the bin.

Symptoms of a bad door bin include:

• Cracks or splits in the bin
• Difficulty securely attaching the bin to the door
• The bin sagging or not holding items properly
• Items frequently falling out of the bin

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement bin assembly for select refrigerators restores secure, organized storage so contents stay contained and accessible, helping prevent spills or tipping during everyday use.

• Provides a dedicated compartment within the fresh food or freezer section to hold items securely
• Snaps or slides into factory rails/hooks for a snug, stable fit
• Helps maintain proper spacing and organization inside the compartment
• Common symptoms: cracked or broken plastic, missing bin, loose fit, falls off or won't stay seated

• Unplug the appliance before servicing
• Remove the old bin; align the new bin with the door or compartment rails/hooks and press or slide into place until fully seated
• Verify secure engagement before loading; avoid overloading to prevent damage
• Hand-wash with mild soap; avoid high-heat dishwasher cycles that can warp plastics

This bin assembly is a replacement clear storage bin for the refrigerator door or interior shelving, restoring secure, visible storage for produce and packaged foods. It replaces a cracked, broken or missing bin to keep items contained and easy to access. What it does:

• Provides a durable, clear compartment for storing food items on the refrigerator door or shelf.
• Restores proper containment when original bin is cracked, split, or missing.
• Keeps stored items visible for quick access and inventory.
• Prevents items from shifting or falling during normal door use.

• Remove existing damaged bin by lifting and sliding out per your model's door/shelf design.
• Align replacement bin with door/shelf rails and slide or snap into place until secured.
• Do not overfill or overload the bin; uneven weight can stress mounting points.
• Use caution handling edges; wear gloves if plastic is cracked to avoid cuts.

This part number contains one (1) screw.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.