Parts for Frigidaire FRSS2323AB1: Refrigerator Door Parts

This door gasket seals the perimeter of the appliance door to keep cold air in and humid air out. Replace a torn, warped, or leaky gasket to restore stable temperatures, reduce frost/condensation, and help the unit run efficiently. What it does:

• Creates an airtight seal between the door and cabinet
• Helps maintain proper temperature and humidity inside the compartment
• Reduces frost buildup and condensation around the door opening
• Common failure signs: tears, gaps, warping, hard or cracked rubber, door not closing flush, warm spots

• 1 door gasket

• Unplug the appliance and clear items from the affected door.
• Condition the new gasket to remove shipping kinks by laying it flat and warming it (soak in warm water or use gentle, low heat).
• Remove the old gasket; on some models you may need to loosen liner-retainer screws to release it.
• Fit the new gasket into the channel, working from the corners; ensure it seats evenly all around and verify a uniform seal.

This replacement access panel cover protects internal components and restores the appliance's finished appearance. It keeps wiring and controls enclosed to reduce debris buildup and accidental contact. What it does:

• Covers and protects internal control or wiring areas from dust, spills, and physical damage
• Prevents accidental contact with electrical components for improved safety
• Stops rattling or vibration noises caused by a missing or loose cover
• Restores a clean, finished look to the appliance exterior or interior

• One replacement access panel cover

• Disconnect power (unplug or shut off breaker) before starting any work
• Use basic hand tools to remove fasteners; keep hardware for reuse
• Handle cover carefully to avoid cracking plastic or scratching finished surfaces

The Handle is an OEM part for Frigidaire refrigerators. This part is responsible for providing a secure grip and facilitating the opening and closing of the refrigerator door.  

Causes of a damaged or ineffective refrigerator door handle can include normal wear and tear from daily use, accidental impacts that result in cracks or breaks, and loosening of the handle's fittings over time. 

Symptoms of a bad refrigerator door handle include:

• Difficulty in opening or closing the refrigerator door.
• A loose handle that moves or wobbles when touched.
• Visible damage, such as cracks or breaks, that can also pose safety risks.
• The handle detaching from the door, requiring immediate replacement for proper operation.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This #10-32 x 3/4-inch machine screw secures appliance components such as panels, brackets, and handles. Using the correct length and thread helps restore a snug, rattle-free hold wherever this screw is specified by the manufacturer.

• Fastens components with a #10-32 machine thread and 3/4-inch length
• Helps keep panels, trim, brackets, or handles secured and aligned
• Replaces missing, stripped, or corroded hardware
• Common signs include loose or wobbly parts, rattling, missing screws, or damaged screw heads/threads

• Disconnect power before servicing; if working near a water connection, shut off the water supply
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping plastic or threads
• Reuse any model-specific washers or spacers if present

This door bushing kit replaces worn hinge bushings that keep refrigerator/freezer doors aligned for smooth, stable operation. Restores proper door rotation to reduce sagging, rubbing, and noisy or stiff hinges. What it does:

• Provides replacement hinge bushings that support the door on its hinge pin for correct alignment
• Helps stop door sag, scraping, and uneven gaps that let cold air escape
• Reduces hinge noise, sticking, and rough door movement
• Fits into the door hinge assembly to restore smooth pivoting action

• Always unplug the appliance or disconnect power before starting repairs
• Support the door while removing hinge pins to prevent dropping or damage
• Remove old bushings from the hinge housing and press or snap new bushings into place; reassemble hinge and confirm alignment

This refrigerator dispenser bearing supports the auger shaft so it spins smoothly during ice dispensing. Replacing a worn bearing restores quieter, more reliable ice delivery and helps prevent binding or uneven crushing of cubes. What it does

• Supports and centers the ice auger/crusher shaft inside the ice bucket
• Reduces friction to allow smooth, consistent rotation
• Wear can cause grinding or squealing during dispensing
• Symptoms include slow/no ice dispensing, jamming, or intermittent operation

• 1 bearing

• Disconnect power and turn off the water supply before service
• Remove the ice bucket and disassemble the crusher housing to access the bearing
• Note the bearing's orientation; transfer any spacers or clips as found
• Reassemble carefully and ensure the auger turns freely by hand before restoring power

This bin assembly replaces a damaged or missing storage bin in your refrigerator, restoring secure, organized storage so items stay contained and the compartment functions as designed. What it does:

• Holds and organizes items in the designated location for your model
• Keeps contents contained to help prevent spills or items sliding/falling
• Maximizes usable space and helps maintain an orderly compartment
• Common signs it's needed: cracked plastic, broken mounting tabs, bin won't stay seated or falls off

• 1 bin assembly

• Remove the old bin and any contents; clean the area if needed
• Align the new bin with the model's hooks/slots and press or snap into place—do not force
• Confirm placement matches your model's diagram for a secure fit
• Avoid overloading; distribute weight evenly to prevent future damage

The Door Shelf Bin is an OEM component for Frigidaire refrigerators. Situated inside the refrigerator door, this removable tray provides convenient storage for condiments and other small items.

Causes of a bad door shelf bin can include cracks or fractures from repeated loading/unloading, or wear to mounting brackets compromising secure placement.

Symptoms of a bad door shelf bin include:

• Failure to properly click into mounting rails
• Warped plastic unable to hold contents inside
• Cracks or breaks exposing stored items to spills

Note: Approximately 13” x 8”

Also compatible with Electrolux models, restored functionality and capacity ensure contents are neatly positioned at hand.

This part number contains one (1) screw.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.