Parts for Whirlpool WRB329DMBB02: Refrigerator Door Parts

This replacement outer door restores the appliance's sealed closure and finished exterior, helping maintain temperature control and a clean appearance. It fits the original mounting points and matches the factory styling. What it does:

• Replaces a cracked, dented, or scratched outer door panel to restore appearance
• Restores proper closure to help maintain internal temperature and seal
• Provides the factory finish and mounting interface for a like-for-like replacement
• Helps eliminate rattling or misalignment caused by a damaged door

• Disconnect power and remove contents before starting any repair
• Handle carefully—edges and internal components may be sharp or fragile
• May require removal of trim, hinges, or brackets for installation; keep original fasteners

This clear refrigerator door bin snaps into the inner door liner to hold bottles, jars, and condiments. Replace a cracked or missing bin to restore secure door storage and keep frequently used items organized and within reach.

• Provides removable shelf storage on the refrigerator door
• Replace if the bin is cracked, warped, or has broken locking tabs
• Common symptoms: bin falls off, won't stay seated, or won't install securely
• Restores proper door capacity and helps prevent spills

• Remove the old bin by lifting up and out of the door slots
• Align the new bin's hooks with the door slots and press down firmly until fully seated
• Ensure both ends are fully engaged; test with a light load before filling
• Distribute weight evenly and avoid overloading

This stop-door is a small replacement door stop that helps control how the appliance door closes and rests, restoring proper door movement and preventing over-travel or binding. What it does:

• Cushions and limits the door's travel to prevent slamming or over-rotation.
• Helps the door align and latch correctly when closing.
• Can reduce door sag or rubbing caused by a worn/missing stop.
• Addresses symptoms such as a door that closes too far, hangs unevenly, or doesn't sit flush.

• High-level, two-person recommended for larger doors; support the door before removing fasteners.
• Disconnect power (and water if applicable) and follow manufacturer safety guidance before servicing.
• Use appropriate hand tools; inspect adjacent hinges and fasteners and replace if damaged.

The Door Shelf Bin is an OEM replacement part for Whirlpool refrigerators. It is a specialized storage compartment designed to fit the refrigerator door, providing convenient and organized storage space for smaller items such as condiments, jars, or bottles. The bin measures approximately 15 inches wide, 3 inches high, and 6 inches deep.

Causes of a damaged or unusable door shelf bin can include physical impact, cracks or breaks due to excessive weight or pressure, or general wear and tear over time.

Symptoms of a door shelf bin that needs replacement include:

• Cracked or broken shelves, making it difficult to store items securely
• Warping or misshaping, preventing a proper fit in the door compartment
• Missing or loose components, resulting in items falling out or shifting during use

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This name plate is the appliance identification label that displays model, serial and rating information and restores the unit's factory appearance. It helps ensure readable identification for service or resale. What it does

• Replaces a missing, faded or damaged identification label so model and serial info are visible.
• Provides required equipment ratings and manufacturer markings used during diagnostics and parts replacement.
• Restores exterior appearance where the original name plate is worn or peeling.
• Helps technicians and homeowners quickly confirm appliance identity during repairs.

• Name plate (single label)

• Disconnect power to the appliance before attempting installation or working near electrical connections.
• Clean and dry the mounting area; some name plates attach with adhesive while others fasten with screws—use the original hardware if present.
• Avoid bending or creasing the label when aligning it; press firmly to ensure full contact for adhesive-mounted plates.

The Fip Gasket is an OEM part compatible with Whirlpool refrigerators. Located around the refrigerator door opening, the fip gasket forms an air seal when the door is closed. 

Causes of a bad fip gasket can include tears, cracks or compression issues from years of door opening/closing cycles. Mineral or food residue buildup can also cause sealing problems.

Symptoms of a bad fip gasket include: 

• Fluctuating interior temperatures  
• Higher energy costs due to inefficient sealing
• Condensation or frost buildup around the door 
• Warm or cool air detected entering around the door seal
• The door not sealing closed properly

This OEM Whirlpool replacement fip gasket is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore refrigerators. 

This refrigerator door gasket replaces a worn seal to restore a tight, even closure around the door. A proper seal keeps cold air in and moisture out, helping maintain temperature, reduce frost, and minimize run time. What it does:

• Forms a tight seal between the door and cabinet frame
• Helps maintain set temperatures and reduce moisture intrusion
• Resolves frost or condensation at the door and frequent compressor cycling
• Common signs: torn, cracked, or warped gasket; gaps; door not sealing smoothly

• Includes: 1 door gasket

• Disconnect power before servicing; remove or secure contents for safety
• On many models, loosen the inner-liner screws or pull the old gasket from the retainer/channel to remove
• Warm the new gasket (warm water or low heat from a hair dryer) to relax shipping folds
• Seat corners first, then press the rest into the retainer; verify seal with a paper-slip test and adjust as needed

This door gasket seals the dishwasher door opening to keep wash water and moisture inside the tub. A fresh, flexible seal helps prevent leaks and improves cleaning performance by maintaining proper pressure and heat.

• Creates a watertight seal between the tub and door perimeter
• Helps prevent leaks at the bottom and sides of the door
• Helps resolve symptoms like water on the floor, moisture around the door, long dry times, or visible tears/flattening of the old gasket
• Restores proper door compression and wash chamber containment

• Disconnect power and turn off water supply before service
• Remove the old gasket from the channel; clean the groove of debris and residue
• Press the new gasket evenly into the channel, centering at the top and working down both sides
• Close the door to help seat the gasket; a short run cycle may help it conform

Color: Black

Color: White

Color: Stainless

The Door Handle is an OEM part for Whirlpool refrigerators. It is a component that facilitates easy access to the fresh food and freezer compartments. The handle interfaces directly with users to open and close refrigerator doors.

Causes of a bad door handle can include wear and tear over time from repeated use, or damage such as cracks, chips or breaks from accidental impact. Temperature fluctuations from frequent door openings can also cause handles to warp or fail prematurely.

Symptoms of a bad refrigerator door handle include:

• Difficulty opening or closing the refrigerator door
• The door not latching securely
• Internal components like springs or cables becoming loose or worn

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement screw fastens appliance panels and components securely. Replace a missing, stripped, or corroded original to restore a tight fit and help prevent rattling, vibration, and gradual loosening of assemblies.

• Secures panels, brackets, and internal assemblies to the frame
• Replaces damaged or missing hardware to maintain proper fit
• Helps reduce vibration, noise, and movement caused by loose parts
• Supports correct alignment at the original mounting points

• Disconnect power and shut off water or gas before service.
• Match the original screw's location and length; replace one at a time if needed.
• Use the correct driver/bit and avoid overtightening to prevent stripping plastic or metal.
• Reuse any washers or clips only if in good condition.

This handle plug snaps into the handle opening to cover the exposed mounting hole and restore a clean, finished look. Replacing a missing or damaged plug also helps keep debris out of the handle cavity.

• Covers the handle's exposed screw/mounting hole for a finished appearance
• Snaps in for a secure, flush fit
• Helps keep dust and moisture out of the handle opening
• Common symptoms: missing plug, cracked or loose cap, visible hole in the handle

• Disconnect power if working near electrical components and allow any hot surfaces to cool
• Protect the finish; use a plastic pry tool to remove the old plug
• Align the new plug with the opening and press firmly until it seats flush
• Replace additional plugs as needed for a uniform look