Admiral Washer LAT7304AGE Leaking

The Mounting Stem Repair Kit is an OEM part for Whirlpool washing machines. It includes all necessary components to repair the mounting stem, which is a critical part of the washer's tub support system. Comes with the hub assembly, seal, and spanner nut. 6-2040130 should also be replaced at the same time. A spanner wrench is required to complete the repair TB123B.

Symptoms of a bad mounting stem include:

• Excessive noise or vibration during the spin cycle.
• The washer tub appearing loose or off-balance.
• Leakage around the central area of the washer, indicating a possible seal failure.

Causes of a bad mounting stem can include wear and tear from normal usage, especially with heavy loads, or corrosion and material fatigue that weaken the stem's integrity.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Siphon Break is an OEM part for Whirlpool washing machines. It is a critical safety component that prevents the backflow of contaminated water from the washer into the fresh water supply line. For the gasket use part number [AP6005834], For the siphon elbow use part number [AP4024083]

Causes of a faulty siphon break include physical damage, clogging due to mineral buildup or debris, or general wear and tear over time.

Symptoms of a bad siphon break:

• Water leaks or puddles around the washing machine
• The washer not filling with water properly
• Potential for contaminated water to enter the fresh water supply

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models. 

The Tub Bearing Kit is an OEM part for Whirlpool washers. It includes all the necessary components to replace the tub bearing which is responsible for supporting the inner tub and allowing it to spin smoothly during the wash cycle. Over time, the bearing may wear out or become damaged, leading to excessive noise, vibrations, or even leaks from the washer.

Causes of a bad tub bearing can include regular wear and tear, exposure to heavy loads or unbalanced loads that put excessive strain on the bearing, or damage due to water leaks.

Symptoms of a bad tub bearing include:

• Excessive noise or grinding during the wash cycle.
• Vibrations or shaking of the washer.
• Leaks from the washer, around the tub area.
• The inner tub not spinning or becoming stuck.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Note: It is advised to replace the Mounting Stem Repair Kit, part number 6-2040130 at the same time.  To complete the repair, you’ll also need a Spanner Wrench to complete the repair (TB123B).

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

This washer injector (lower) forms the bottom half of the fill injector assembly, channeling incoming water cleanly into the tub. A damaged injector can cause leaks or spray at the tub ring during fill. What it does:

• Directs fill water into the tub through the injector assembly
• Seals with the upper injector to prevent splashback
• Common symptoms: leaking or spraying during fill, water on floor near the top/front during fill, visible cracks/warping on the injector
• Restores a clear, sealed water path for proper filling

• One lower injector

• Disconnect power and shut off water supply before servicing
• Access may require lifting the top or removing the cabinet to reach the injector at the tub ring
• Transfer any reusable clamps/retainers; align with the upper injector for a proper seal
• Run a short fill and inspect for leaks after installation

The Water Injector is an OEM part for Whirlpool washing machines. This component is responsible for distributing water into the washing machine during the wash cycle, ensuring that clothes are thoroughly saturated and cleaned. It connects to the water supply and directs water into the tub at the appropriate times.

Common causes of a bad water injector include blockages from mineral deposits, wear and tear from frequent use, or damage due to high water pressure. Over time, the injector's effectiveness can diminish, impacting the washing machine's performance.

Symptoms of a bad water injector include:

• Insufficient water entering the washing machine
• Longer fill times or failure to fill at all
• Poor cleaning performance
• Leaks or drips around the injector area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Drain Hose is an OEM part for Whirlpool washing machines. It is responsible for carrying wastewater from the washing machine to the household drain system, ensuring proper removal of water during and after the wash cycle.

Common causes of a bad drain hose include wear and tear over time, blockages from debris or lint, and damage from sharp objects or improper installation.

Symptoms of a bad Drain Hose include:

• Water leaks from the hose
• Slow or incomplete drainage
• Visible cracks, splits, or punctures
• Unpleasant odors from trapped debris

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Tub Cover Gasket is an OEM part for Whirlpool washing machines. This part creates a watertight seal between the tub cover and the tub, preventing water from leaking during the wash cycle. 

Causes of a bad gasket include exposure to harsh detergents, regular wear and tear, or improper installation. 

Symptoms of a bad tub cover gasket include:

• Water leaking from the washing machine
• Excessive moisture around the tub cover area
• Visible cracks or wear on the gasket
• Unusual noises during the wash cycle due to improper sealing

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This tub cover and gasket seal the top of the outer tub to contain splashing and prevent leaks during wash and spin. Replacing a cracked cover or compressed gasket restores a tight rim seal and cleaner operation. What it does:

• Creates a watertight seal at the outer tub rim
• Helps reduce splash-over and directs incoming water flow
• Helps keep clothing and debris out of the gap between basket and outer tub
• Common symptoms: leaks from the top/front, visible cracks in the ring, or a brittle/torn gasket

• One tub cover and one perimeter gasket

• Disconnect power and turn off the water supply before servicing
• Access the tub area; release retaining clips/screws and detach any inlet/flume from the old cover
• Clean the tub rim thoroughly; seat the new gasket evenly and install the cover without pinching the seal
• Reuse existing fasteners/clips; ensure the cover is fully latched all around and do not overtighten

This upper injector directs incoming water cleanly into the washer tub during fill and rinse. Replacing a cracked or clogged injector restores proper water delivery, helps prevent splash-back, and supports consistent wash performance.

• Channels inlet water into the tub from the upper injection point
• Helps prevent splash-back and backflow at the tub ring area
• Promotes even water spray for detergent/softener flushing as designed
• Common failure symptoms: water dripping or spraying from the fill area, leaks down the cabinet, slow/erratic fill, or visible cracking/mineral buildup on the injector

• Disconnect power and turn off both hot and cold water supplies before servicing
• Access the injector at the top/tub ring area; remove top or cabinet panels as required per model
• Transfer and secure the fill hose and clamps; ensure a fully seated connection
• Restore water and power, run a fill test, and check all connections for leaks

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

This gasket creates a reliable seal between two appliance components. Replacing a worn or damaged gasket helps stop leaks and drafts at the joint, restoring proper performance and preventing moisture, frost, or debris from entering where parts meet.

• Forms a tight seal between mating surfaces to help prevent water or air leaks
• Helps maintain proper temperatures and operation by keeping unwanted air or moisture out
• Reduces vibration at the joint that can cause noise or loosening over time
• Typical failure signs: visible cracks or flattening, seepage or drips at the joint, moisture or frost forming nearby

• Disconnect power and shut off water supply before service
• Photograph the original setup to aid reassembly
• Remove the old gasket and thoroughly clean/dry both mating surfaces; remove any residue
• Seat the new gasket evenly without stretching; tighten fasteners evenly and check for leaks or air gaps after reassembly

This small retaining clip secures components in place inside the appliance, helping prevent movement, vibration, and premature wear. Replace a bent, fatigued, or missing clip to restore a solid, factory-tight hold.

• Holds panels, brackets, or tubing securely in their mounts
• Helps maintain alignment to reduce rattles, rubbing, or intermittent issues
• Common signs of failure: missing clip, loose fit, buzzing/vibration, parts that won't stay seated
• Restores proper retention after service, transport, or vibration-related fatigue

• Disconnect power and shut off gas/water before servicing
• Note the original clip's orientation; remove with needle-nose pliers
• Seat the new clip fully—do not over-bend; spring tension provides the hold
• Test operation before reassembly

This small clamping nut secures a mating clamp or bracket so the connected component stays firmly in place. Replacing a worn, stripped, or missing nut restores a solid hold and helps prevent looseness or leaks around the secured area.

• Secures a clamp or bracket to its mounting point
• Restores proper clamping force when the original nut is stripped or missing
• Common signs: loose clamp, rattling/vibration, clamp won't tighten, minor leaks where the clamp is used
• Durable hardware replacement to maintain stable, reliable assemblies

• Disconnect power and shut off water/gas to the appliance before service
• Note clamp/bracket orientation before removal for correct reassembly
• Start threads by hand to prevent cross-threading; then tighten with the appropriate tool
• Do not overtighten—snug just enough to securely clamp the component

This siphon break elbow is a 90-degree connector used in the drain path to create an air break that helps prevent back-siphoning. Replacing a cracked or obstructed elbow can stop leaks and restore proper draining performance.

• Provides a 90-degree connection between the drain hose and the siphon break/air-gap fitting
• Maintains the atmospheric break that prevents wastewater from siphoning back into the appliance
• Helps route drain flow without kinking or stressing the hose
• Common symptoms: leaking at the elbow area, water backing up through the drain line, slow or incomplete draining, visible cracks or damage

• Disconnect power; turn off water supply if applicable
• Expect residual water—protect the area with towels or a pan
• Release hose clamps, note orientation, fully seat hoses on the new elbow, and secure clamps
• Run a test and check for leaks

This retaining washer secures a center-mounted component within the assembly, keeping parts aligned and in place during operation. Replacing a worn or missing washer helps prevent looseness, vibration, and noise for more reliable performance. What it does:

• Holds a component on a center shaft or stud to prevent axial movement
• Maintains proper alignment under rotation and load
• Can reduce wobble, rattling, or scraping noises from a shifting assembly
• In applicable washers, can help restore consistent agitation or spin when parts have been moving out of place

• 1 retaining washer

• Disconnect power and water before servicing; wear cut-resistant gloves
• Note the order and orientation of all spacers, washers, and clips during disassembly
• Clean mating surfaces and ensure the washer is fully seated before reassembly
• Inspect adjacent hardware for wear or damage and replace as needed

This agitator seal assembly sits at the agitator/drive-shaft pass-through to keep wash water inside the tub and away from the drive system. Replacing a worn seal helps stop center-post leaks and protects internal components from moisture.

• Seals the opening where the agitator/drive shaft passes through the tub or centerpost
• Helps prevent water from migrating into the centerpost/gearcase area
• Supports reliable agitation and spin by keeping contaminants out of the drive assembly
• Common symptoms of failure: water leaking from the center of the tub or beneath the washer, or rust/water tracks around the agitator hub

• Disconnect power and shut off water; wear gloves and eye protection
• Remove agitator cap and fastener, then lift the agitator to access the seal (procedure varies by model)
• Note the original seal orientation; clean mating surfaces and install the new seal squarely (lightly lubricate only if specified by the manufacturer)
• Reassemble and run a short fill/agitate test while observing for leaks