Estate Washer TAWX700JQ1 Will not drain or doesn't drain

The Washer Lid Switch is an OEM replacement part for Whirlpool washers. It is an electronic component located inside the washer lid that detects when the lid is open or closed in order to activate the necessary functions during the wash cycle.

Symptoms of a bad Washer Lid Switch include: 

• The wash cycle will not start even when the lid is closed
• Error codes displayed related to the lid being open 
• Inability to advance through cycle selections
• Flashes or other improper lid switch behavior

Causes of a bad lid switch can be normal wear and tear over time. Moisture exposure may also contribute to internal component failure.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

The Direct Drive Washer Pump is an OEM part for Whirlpool washing machines. It is responsible for pumping water out of the washer during the drain cycle, ensuring that the washing machine drains efficiently after each wash.

Causes of a bad direct drive washer pump can include blockages from debris or foreign objects, wear and tear from regular use, damage to the pump impeller, or electrical issues affecting the pump motor. Over time, these factors can hinder the pump's performance, leading to operational issues.

Symptoms of a bad direct drive washer pump include:

• Washer not draining water properly
• Unusual noises during the drain cycle, such as grinding or humming
• Water leaks from the bottom of the washer
• Washing machine stopping mid-cycle due to drainage issues

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Related item: Motor coupling 285753A.

The Retainer Clip is an OEM replacement part for Whirlpool direct drive washing machines.

Causes of a bad retainer clip can include wear and fatigue from continuous vibration over many wash cycles. Cracks or breaks in the plastic material may develop as well.

Symptoms of a bad Retainer Clip include:

• Water leaks detected around the pump area inside machine cabinet
• Loosening of hoses or tubes interrupting proper drainage flow
• Potential pump component detachment from disconnected lines
• Damage to neighboring components submerged by leaked water

The OEM Whirlpool part is also compatible with Maytag, Jenn-Air, and select Kenmore models.

The Lid Strike is an OEM part for Whirlpool washing machines. This small yet essential component ensures that the washer lid is securely latched, allowing the machine to operate safely and effectively. The lid strike interacts with the lid switch, enabling the washer to detect when the lid is closed and allowing the washing cycle to proceed.

Over time, the lid strike can become worn out or damaged due to regular use, accidental force, or misalignment. A faulty lid strike can prevent the washing machine from recognizing that the lid is closed, thereby hindering the operation of the machine.

Symptoms of a bad lid strike include:

• The washer not starting or stopping mid-cycle
• Error messages indicating the lid is open when it is closed
• Difficulty in latching the lid securely
• The lid strike appearing broken or misaligned

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This mechanical timer sequences your washer's cycles, routing power to the motor, pump, and valves. Replacing a failing timer can restore proper advancing through wash, rinse, and spin so cycles complete reliably. What it does:

• Controls the order and duration of fill, agitate, drain, and spin functions
• Directs power to components based on the selected cycle and options
• Common failure symptoms include cycles that won't advance, stopping mid-cycle, or no agitation/spin in specific settings
• Requires manual knob advancement to proceed through stages when failing

• 1 timer assembly

• Disconnect power before servicing
• Access the timer in the control console; photograph or label wire positions
• Transfer wires one at a time to the new timer, mount it, and reinstall the control knob/dial as designed
• Run a test cycle to ensure the timer advances through all stages